Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 19

Страница: 19 / 58

2022

congatec

GmbH

CET0m10

19/58

5.2

Power Supply Connectors

The conga-MEVAL provides the following connectors for power supply:

•

standard 24-pin ATX conector (X59)

•

12 V DC banana jack (M22 and M23)

•

optional DC banana jack for supplying power to the module (M29 and M30)

Note

In ATX mode, the +3.3 V, +5 V and +12 V are derived from the ATX power supply. If 12 V DC power is supplied via the DC banana jack, the

onboard DC/DC regulators will generate 3.3 V and 5 V.

Caution

1. Do not exceed the voltage rating of the COM Express module. Doing so will damage the module.

2. Do not supply power to both the DC banana jack and the ATX connector at the same time.

5.2.1

Standard ATX Connector

The conga-MEVAL provides a 24-pin ATX connector (X59). Use jumper X58 to select ATX or AT power supply mode. Use jumper X60 to
disconnect the 5 V standby voltage from the whole system.

The conga-MEVAL also provides a 4-pin ATX connector (X128). This connector can be used together with connector X59 if higher current is
expected.

Table 4

X58 - ATX PSU Control Description

Configuration

Description

1-2

ATX mode (default)

Module starts after pressing power-on button M19

2-3

AT mode

Module starts after switching on the power supply

Table 5

X60 - ATX 5V Standby Connection

Description

1-2

5V standby connected (default)

2-3

5V standby disconnected

X58

M19

X60

Содержание COM Express conga-MEVAL

























































Результаты поиска

Содержание COM Express conga-MEVAL

Отзывы:

Congatec COM Express conga-MEVAL, Руководство пользователя, Страница: 19 / 58

Результаты поиска

Содержание COM Express conga-MEVAL

Отзывы: