Congatec 065450 Скачать руководство пользователя страница 20

Страница: 20 / 75

2020

congatec

DSTXm10

20/75

4.1.3

CMOS Battery Connector

The conga-STX7 provides battery holder M20 for attaching CR2032 CMOS battery. The battery supplies power to maintain the CMOS settings
and real time clock.

Use jumper X31 to connect the RTC battery and jumper X49 to disconnect the RTC battery.

Table 6

X31/X49 Description

Jumper

Description

X31

Jumper connects RTC battery (default)

X49

Jumper disconnects the RTC battery

Warning

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

Connector Type

X31, X49: 2.54mm, 1 x 2-pin header

4.1.4

Status LEDs

The table below describes the conga-STX7 status LEDs.

Table 7

Status LED Description

LED

Color

Status

Description

Power

All

Off

No power applied to board and BMC

BMC Heatbeat

Green

On (blinking)

BMC activity is detected. In BMC normal operation, the LED blinks at an interval of 0.5 s.

Constant blinking indicates blank SPI ROM or abnormal operation.

Off

BMC is not active

HDD

D30

Yellow

On (blinking)

Disk activity detected

Off

No disk activity detected

M20

X31/X49

Содержание 065450




































































Результаты поиска

Содержание 065450

Отзывы:

Бренды по названию

Популярные бренды

Congatec 065450, Руководство пользователя

Результаты поиска

Содержание 065450

Отзывы:

Бренды по названию

Популярные бренды