Congatec 050100 Скачать руководство пользователя страница 60

Страница: 60 / 65

SA70m01

60/65

Table 32 Management Pins Signal Description

Signal Name

Description

I/O

PU/PD

Comment

VIN_PWR_BAD#

S150 Power bad indication from carrier board. Module and carrier power supplies (other

than module and carrier power supervisory circuits) will not be enabled while this

signal is held low by the carrier. Pulled up on module. Driven by OD part on carrier

I VDD_IN

PU 10k

CARRIER_PWR_

S154 Carrier board circuits (apart from power management and power path circuits) should

not be powered up until the module asserts the CARRIER_PWR_ON signal.

O 1.8V

PD 100k

CARRIER_STBY#

S153 The module shall drive this signal low when the system is in a standby power state

O 1.8V

PD 100k

Connected to SUS_S3#

RESET_OUT#

P126 General purpose reset output to carrier board

O 1.8V

PD 100k

RESET_IN#

P127 Reset input from carrier board. Carrier drives low to force a module reset, floats the

line otherwise. Pulled up on module. Driven by OD part on carrier

I OD 3.3V

PU 10k

POWER_BTN#

P128 Power-button input from carrier board. Carrier to float the line in in-active state.

Active low, level sensitive. Should be de-bounced on the module. Pulled-up on

module. Driven by OD part on carrier

I OD 3.3V

PU 10k

SLEEP#

S149 Sleep indicator from carrier board. May be sourced from user Sleep button or carrier

logic. Carrier to float the line in in-active state. Active low, level sensitive. Should be

de-bounced on the module. Pulled-up on module. Driven by OD part on carrier

I OD 3.3V

PU 10k

LID#

S148 Lid open/close indication to module. Low indicates lid closure (which system may use

to initiate a sleep state). Carrier to float the line in in-active state. Active low, level

sensitive. Should be de-bounced on the module. Pulled-up on module. Driven by

OD part on carrier

I OD 3.3V

PU 10k

BATLOW#

S156 Battery low indication to module. Carrier to float the line in in-active state. Pulled up

on module. Driven by OD part on carrier

I OD 1.8V

PU 10k

I2C_PM_DAT

I2C_PM_CK

P122

P121

Power management I2C bus data and clock. On x86 systems these serve as SMB

data and clock

I/O OD 1.8V

PU 2k2

CHARGING#

S151 Held low by carrier during battery charging. Carrier to float the line when charge is

complete. Pulled-up on module. Driven by OD part on carrier

I OD 3.3V

PU 10k

3.3V

CHARGER_

PRSNT#

S152 Held low by carrier if DC input for battery charger is present. Pulled up on module.

Driven by OD part on carrier

I OD 3.3V

PU 10k

3.3V

TEST#

S157 Held low by carrier to invoke module vendor specific test function(s). Pulled up on

module. Driven by OD part on carrier

I OD 3.3V

PU 100k

3.3V

SMB_ALERT_1V8#

SM Bus Alert# (interrupt) signal

I OD 1.8V

PU 2k2

Содержание 050100

































































Результаты поиска

Содержание 050100

Отзывы:

Бренды по названию

Популярные бренды

Congatec 050100, Руководство пользователя

Результаты поиска

Содержание 050100

Отзывы:

Бренды по названию

Популярные бренды