97 Witmer Road
North Tonawanda, New York 14120-2421
Toll Free U.S. 800-635-3213
FAX 716-694-3102
www.conferladders.com
Printed in U.S.A.
MADE IN THE U.S.A. by:
OPTIONAL ACCESSORY
SKIM-IT
SKIMS OFF DEBRIS Cut cleaning time 75% with skimmer
extension that guides debris directly into your skimmer. Fits most
in-ground and above-ground pool skimmers. Corrosion-resistant
plastic Skim-It installs in seconds without tools.
OPTIONAL CONVERSION KIT
To easily convert your A-frame ladder to a deck/inpool ladder order
our #CK7100 conversion kit. The kit includes all parts and
hardware needed
5
6
MODEL #7100X
A-FRAME LADDER
LADDER MUST BE ATTACHED TO POOL FRAME...
DO NOT USE WITH INFLATABLE POOLS
ASSEMBLY AND INSTALLATION MANUAL
Made in U.S.A. by
SAVE THESE INSTRUCTIONS
DEALER/INSTALLER: GIVE TO HOMEOWNER
The Anti-Entrapment Barrier is included in this ladder for the U.S. and Canada only, as required by ANSI/APSP.
The Anti-Entrapment Barrier is NOT intended as a substitute for competent adult supervision.
If you would like to purchase the barrier, please visit our website at: www.conferladders.com
CP-7100X 15M 09/12
CONFER PLASTICS, INC. FIVE YEAR WARRANTY
Confer Plastics, Inc. warrants their swimming pool ladders and steps to be free from defects in
workmanship for five years from date of purchase.
DO NOT RETURN DEFECTIVE PART TO DEALER
E-MAIL CONFER PLASTICS AT:
A PICTURE [S] OF DEFECTIVE PART, A BRIEF DESCRIPTION OF PROBLEM,
PROOF OF PURCHASE AND YOUR CONTACT INFORMATION.
INFORMATION MAY ALSO BE FAXED TO CONFER PLASTICS AT:
716-694-3102
OR MAILED TO THE ADDRESS BELOW. UPON REVIEW OF THE INFORMATION YOU
WILL BE NOTIFIED IF PART IS COVERED UNDER THE WARRANTY AND
THE SHIPPING/HANDLING CHARGES.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Confer Plastics, Inc.
97 Witmer Road
North Tonawanda, N.Y. 14120-2421
IMPORTANT
FOR YOUR SAFETY
* Check the contents of the carton with the Parts list
for this ladder.
*
If any parts are missing call Toll Free U.S. -
800-635-3213 or visit our web site at
www.conferladders.com
*
DO NOT
attempt to assemble or install the ladder
if there are
ANY
shortages of parts or hardware.
*
For proper assembly and installation follow all
instructions in the sequence shown.
*
Before using the product, after assembly and
installation, go over the instructions and procedures
again to make sure nothing has been overlooked.
*
Be sure and safe. The manufacturer
IS NOT
responsible for improper assembly, installation
and use.
SAFETY RULES
*
Locate ladder on a solid base.
*
One person on the ladder at a time.
*
Ladder
MUST
be installed per manufacturerʼs
instructions.
*
DANGER:
No Jumping or Diving from ladder.
*
Face ladder when entering and leaving pool.
*
To prevent entrapment or drowning —
DO NOT
swim through, behind or around ladder.
*
Ladder to be used as a swimming pool ladder only.
*
Weight limit -
300 lbs maximum
*
Warning:
Exceeding the maximum weight
restriction may cause the ladder to fail.
*
When ladder is not in use lock up outer treads with
padlock provided in hardware bag.
*
Consult your local Building Department before
installation of your pool and equipment.
*
DANGER:
Use a cordless drill for assembly
and installation. NEVER use an electric drill in
or around the pool.
Winterizing:
To winterize your ladder pull the ladder from the pool,
remove the plugs, lay the ladder on its side to allow the water to drain out.
A small amount of water left in the ladder will not cause any damage.
Replace the plugs into the fill holes so that they do not get lost.
The ladder may be left outside.
IMPORTANT: WHENEVER THE POOL IS NOT IN USE
THE OUTER TREADS MUST BE IN THE UP POSITION
AND LOCKED WITH THE INCLUDED PADLOCK.
IMPORTANT: LADDER ADAPTER KIT
LAK
kit fits Confer A-frame ladders for use with non-traditional
metal framed swimming pools with a wall height of 48” - 54”.
Use with models: 7100b, 7100x, 7000b and 7200.
ATTACH LADDER TO POOL
For maximum stability, the ladder must be
fastened to the top of the pool. Postion the
ladder at the desired location on the pool top
seat and mark the two locations of the holes in
the platform onto the top seat. Move the
ladder away, and being careful not to damage
the liner, drill two holes through the top seat.
Fasten the ladder platform to the top
seat using two 1/4-20 x 2-1/4” bolts, 1/4” flat
washers, and 1/4-20 hex nuts.
IF YOU HAVE A NON-TRADITIONAL METAL
FRAMED POOL PLEASE REFER TO
LADDER ADAPTER KIT BELOW
PLACE LADDER IN POOL
Fill the two inner legs with water and cap the
fill holes with plugs. Cap the fill holes in the
two outer legs; do not fill outer legs with water.
Place the ladder over the pool top seat with
the swing up treads on the outside of the pool.
Tip the ladder sideways to allow the treads to
fill the water. This will prevent floating. The
platform should rest on the pool top seat and
the bottom tread should rest firmly on the pool
bottom. If they do not, the extension boots may
be adjusted up or down as required to
achieve the best fit.
25.
LAK KIT
Check for availability at your local pool dealer or order online at
www.conferladders.com
24.
Confer 7100X-9/13:Confer 7100_2_07 10/7/13 11:55 AM Page 1
