manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 68

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 68 of 128 

6.3.3.5.2

 

Mounting the expansion module with a setting aid 

 

Requirements: 

 

The conductor rail system is fully mounted up to the position of the expansion module. 

 

The distance from the system edge to the last hanger clamp must be 125 mm. Move a hanger clamp if necessary (see Fig. 70). 
If a hanger clamp must be moved or supplemented with another hanger clamp, the distance to the next hanger clamp must not 
be greater than 500 mm 

 

Fig. 70: Distance from the system edge to the last hanger clamp 

 

 

If the setting aids are available (Pos. 1 Order No.: 08-S902-0002P), these must be inserted in each expansion gap of the expan-
sion module (Pos. 2) in such a way that they cannot be lost (see Fig. 71 to Fig. 72). 
 

 

 

Fig. 71: Setting aids (Pos. 1) inserted in each expansion gap of the expansion module (Pos. 2) 

1

2

1

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды