manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 49

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 49 of 128 

 

Fig. 41: Standard hanger clamps for screwing on 

 

Use the QR code (“click” or “scan”), to watch our animation 

Mounting Hanger Clamps (clip-in, screwable and turnable).

 

6.3.3.2

 

Mounting the fixed point 

A fixed point consists of a hanger clamp and 2 fixed point clamps per pole. The positions of the fixed points are determined when 
planning the system. The correct positioning of the fixed points is crucial for the thermal expansion behavior of the conductor rail 
system. 

Establishing a fixed point: 

→

 

Install a fixed point to the left and right of a hanger clamp per conductor rail pole. The fixed point cap is secured by an insertion 

cam in a hole in the side wall of the conductor rail. 

→

 

Scribe the position on the conductor rail before installation. 

→

 

Place the fixed point cap on the conductor rail as a drilling jig and drill a 3-mm hole through the insulation and copper profile on 

one side. 

→

 

Remove the fixed point cap and replace it after rotating through 180° and insert an insertion cam into the hole. 

 

6

5

7

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды