manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 25

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 25 of 128 

4.3

 

Description of the components 

 

Fig. 4: Hanger clamp 0815 

 

Hanger clamp 0815 

Hanger clamps for supporting the conductor rail. The hanger 
clamps listed in the catalog are screwable. In many cases, 
customer-specific hanger clamps that are inserted in the sup-
port profile or are screwed into it are used. The conductor 
rails slide into the hanger clamps longitudinally. 

 

Fig. 5: Rail cross-section PH, PE and PE

plus

 (with protection against 

interchanging) 

 

Fig. 6: PE

plus

 principle 

 

Fig. 7: Conductor rail 

 

Conductor rail

 

Copper rail with PVC insulation as PH and PE as well as 
PE

plus

 rails can be supplied in 4000 mm and special 6000 mm 

lengths on request. PE and PE

plus

  rails are marked in 

green/yellow. Phase rails are yellow. 
Two protective conductor versions — PE and PE

plus 

— are 

available for the conductor rail system. For new systems, the 
PE

plus

 variant with protection against interchanging is used. 

For PE

plus

 rails, the insulation is opened wider for a broader 

PE

plus

 brush. The wider PE

plus

 sliding contacts largely prevent 

(without use of force or damage) the sliding contacts from 
engaging in a phase rail. PE

plus

 end caps are also wider open 

and recognizable by their green color. 
 
PH = Phase conductor 
PE = Protective conductor 
PE

plus

 = Protective conductor with protection against inter-

changing 

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды