Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 105

Страница: 105 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 105 of 128

8.3

Stopping the system

Requirement:

DANGER!

Risk of injury due to electric shock!

→

Disconnect the conductor rail system from the power supply

according to the 5 Safety Rules

and

secure it against being switched back on

. For the 5 Safety Rules, see Section 2.5.

8.4

Continuing operation

WARNING!

Risk of injury if safety equipment and protective devices are disabled!

→

Before switching the system back on, ensure that all covers, safety systems and protective de-

vices are installed and working properly.

Before switching the system back on, ensure that:



The current collector heads are laying within the conductor rail for the entire length and the specified contact pressure must be
applied.



There is no heavy soiling or objects in the conductor rails.

→

Visually inspect the system.



The insulation resistance corresponds to the locally applicable technical guidelines.

→

Each time before the product or system is started, measure the insulation resistance according to locally applicable technical

standards, directives and legal regulations.

8.5

Perform regular maintenance and servicing

Perform regular maintenance and servicing in accordance with Section 9.

WARNING!

Risk of malfunctions!

Lack of maintenance and servicing can cause malfunctions and significant damage.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды