manualshive.com logo in svg

Conductix-Wampfler MultiLine 0835, Инструкция по монтажу

Поделиться
Скачать
Conductix-Wampfler MultiLine 0835 Скачать руководство пользователя страница 7

Mounting Instruction 

 

Conductor rail system 

MultiLine 0835 

 

 

MAL0835-0001c-EN 
www.conductix.com 

translated document 

page 7 of 81 

2

 

Safety instructions 

2.1

 

General safety information 

Safety and hazard information are always marked with corresponding symbols in this mounting instruction. Safety instructions are 
introduced by signal words that signal the scale of the hazard. Always observe safety and hazard instructions, and work carefully 
to avoid accidents, bodily injury and damage to property! 
 

 

DANGER! 

…  indicates an immediate hazard that, if not avoided, may result in death or serious injury. 

 

 

 

DANGER! 

… indicates an immediate hazard due to electrical current, which, if not avoided, may result in death or 

serious injury. 

 

 

 

WARNING! 

…  indicates a potential hazard that, if not avoided, may result in death or serious injury. 

 

 

 

WARNING! 

… indicates a potential hazard due to electrical current, which, if not avoided, may result in death or 

serious injury. 

 

 

 

CAUTION! 

…  indicates a potential hazard that, if not avoided, may result in moderate or minor injury and property 

damage. 

 

 

NOTICE! 

Tips and recommendations: 

… refers to useful tips and recommendations as well as information for efficient and trouble- 
free operation.

 

 

 

Содержание MultiLine 0835


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды