manualshive.com logo in svg

Conductix-Wampfler MultiLine 0835, Инструкция по монтажу

Поделиться
Скачать
Conductix-Wampfler MultiLine 0835 Скачать руководство пользователя страница 16

Mounting Instruction 

 

Conductor rail system 

MultiLine 0835 

 

 

MAL0835-0001c-EN 
www.conductix.com 

translated document 

page 16 of 81 

2.7.3

 

Danger from dust and vapours 

Required protective equipment: 

 

 

DANGER! 

Risk of sensitization, irritations of the mucous membranes and disorders of the respiratory 

tract through dust! 

Dust from the carbon brushes collects in the conductor rails and the guide profile. This dust is very 

fine and is categorized as a health risk. Working a lot with the conductor rail system and/or not 

applying the requisite level of care when handling accumulated dust (e.g. cleaning the system with 

compressed air) can lead to sensitization. People that frequently spend long periods of time inside a 

busy facility without protective equipment may be affected by the 

following

: 

 

Irritation of the mucous membranes

 

 

Diseases of the respiratory tract

 

 

Cancer

 

→

 

At workplaces that are continuously exposed, and also strongly frequented facilities, personnel must 

be protected through effective measures against dust 

→

 

Personal protective equipment must be worn during all works on the conductor rail system during 

which accumulated dust is disturbed  

→

 

The following personal protective equipment must be worn during cleaning operations: 

 

Safety goggles

 

 

Dust mask class FFP3

 

 

Gloves

 

 

Disposable overall

 

→

 

Before starting work, clean the conductor rails according to regulations. See section 12.3 

→

 

Protect the surroundings during cleaning work, for instance by covering or removing warehouse 

goods and blocking access to those areas in which dust could fall down on persons 

→

 

Remove dust with a vacuum cleaner. 

Do not blow out dust with compressed air

 Vacuum 

cleaners should be fitted with a class H fine filter 

→

 

Do not eat and/or drink while cleaning! 

→

 

Do not smoke while cleaning! 

 

 

DANGER! 

Poisonous gases in case of fire! 

In case of fire in the facility, the plastic parts (PVC) of the conductor rail system will generate 

poisonous gases (HCL). 

→

 

Evacuate the building immediately in the event of fire 

→

 

Notify the fire brigade if there is a fire 

 

 

Содержание MultiLine 0835


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды