manualshive.com logo in svg

Condair GC 130, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Condair GC 130 Скачать руководство пользователя страница 7

7

For Your Safety

Condair GS

 

xxxxxxx_A_EN_1905_Condair-GS_OM  

2 

For Your Safety

General

Every person who is tasked with the operation and maintenance 

of the Condair 

GS  humidifier must read 

and understand this manual before performing any work on the unit. Knowing and understanding the 

contents of the Installation Manual, and the Operation and Maintenance Manual is a basic requirement 

for protecting personnel against any kind of danger, preventing faulty operation, and operating the unit 

safely and correctly.
All labels, signs and markings applied to the 

Condair 

GS humidifier must be observed and kept in a 

readable state. 

 

Personnel Qualifications

All procedures described in this manual must only be performed by personnel who are adequately quali

-

fied, well trained and are authorized by the customer.
For safety and warranty reasons, any activity beyond the scope of this manual must only be performed 

by qualified personnel authorized by Condair.
All personnel working with the 

Condair 

GS humidifier must be familiar with, and comply with the appro

-

priate regulations on workplace safety and prevention of accidents.

 

Intended Use

The humidifier is intended exclusively for air humidification using a Condair-approved steam distributor 

within specified operating conditions (refer to 

"Operating Data" on page 68 

for details). Any other type of 

application, without the express written consent of Condair, is considered to be NOT conforming to its 

intended purpose, and may lead to dangerous operation and will void the warranty.
In order to operate the equipment in the intended manner all information contained in this manual, in 

particular the safety instructions, must be observed closely.

Safety Precautions that Must be Observed

DANGER! 

Risk of electric shock!

The Condair 

GS humidifier

 is mains powered. Live parts may be exposed when the access 

panels are removed. Touching live parts may cause severe injury or even death.
Prevention

:

  

Before performing any work inside the 

Condair GS

 humidifier shut down the humidifier 

properly and secure it against accidental power-up as described in 

"Shutting Down" on page 45

.

WARNING!

Wiring errors can cause improper and dangerous operation of the humidifier!

Prevention:

 Tag all wires before disconnecting them. Reconnect all wires correctly after servicing, 

and check the unit functions properly.

CAUTION!

Electrostatic discharge (ESD)!

The electronic components inside the control cabinet in the humidifier are sensitive to elec

-

trostatic discharge (ESD).
Prevention:

 Take appropriate measures to protect the electronic components inside the unit against 

damage caused by electrostatic discharge (ESD). Refer to IEC 61340.

Содержание GC 130









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды