Condair GC 130 Скачать руководство пользователя страница 5

Страница: 5 / 72

Introduction

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

Introduction

1.1

Before You Start!

Thank you for purchasing the

Condair

GS humidifier.

The Condair

GS humidifier incorporates the latest technical advances and meets all recognized safety

standards. Never-the-less, improper use of the

Condair

GS humidifier may result in danger to the user

or third parties, and/or damage to property.
To ensure safe, proper and economical operation of the

Condair

GS humidifier, observe and comply with

all information and safety instructions contained in this manual, as well as all relevant documentation of

components of the installed humidification system. Comply with all local and regional regulations deal

ing with gas, combustion air, flue gases, water, steam and electrical systems.

Adhere to the standards

outlined in AS/NZS 5601 (if applicable).
If you have additional questions, contact your Condair representative. They will be glad to assist you.

1.2

General

Limitations

The subject of this manual is the

Condair

GS humidifier. The various options and accessories may only

be described in-so-far as is necessary for proper installation and operation of the equipment. Additional

information on available options and accessories can be obtained in the instructions that are supplied

with them.
This manual is restricted to the operation and maintenance

of the Condair

GS humidifier, and is intended

for well trained personnel who are suitably qualified for their respective tasks.

Symbols Used in This Manual

CAUTION!

The catchword "CAUTION" in conjunction with the general caution symbol is used to provide safety

instructions that, if neglected, may cause damage and/or malfunction of the unit or damage to

property.

WARNING!

The catchword "WARNING" in conjunction with the general warning symbol is used to provide

safety instructions that, if neglected, may cause injury to personnel. Other specific warning symbols

may also be used in place of the general symbol.

DANGER!

The catchword "DANGER" in conjunction with the general danger symbol is used to provide safety

instructions that, if neglected, may cause severe injury to personnel or even death. Other specific

danger symbols may also be used in place of the general symbol.

Other Related Publications

This manual is supplemented by other publications such as the Installation Manual , Spare Parts List,

etc., which are included in the delivery of the equipment. Where necessary, appropriate cross-references

to these publications have been added in this manual.

Содержание GC 130









































































Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды

Condair GC 130, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды