background image

 

 

Suspension mounting 

 

Suspending the Smoke Screen is achieved using a ‘Suspension Kit’ comprising a length of unistrut, two sections 
of threaded bar and fixings. 

 

Suspension Kit Contents

 

(all M8)

 

 

Unistrut 1 x 1 metre 
Threaded bar 2 x 1 metre 
 
Fixings: 
1 x ceiling hole surround 
2 x drop-in anchors 
6 x full nuts 
4 x 25mm washers 
2 x 38mm washers 
2 x channel nuts

 

 

 

 
 
 
 
 
 
 
 

 

 

Prepare the Smoke Screen by fitting the angle 
brackets. Fix the required length of M8 threaded 
bar to the bracket using 4 x nuts and 4 x 25mm 
washers. 

Fix the unistrut into place.  There are a range of 
fixings to accommodate concrete ceiling, 
girders etc.; if in doubt contact the fixing 
supplier. Attach the threaded bar to the unistrut 
using the channel nuts, 38mm washers and M8 
nuts. Once this is done the Smoke Screen can 
be lifted into position and the set screws 
tightened as above. 

Any fine adjustments can be made at this stage 
as the nuts and the threaded bar will take the 
weight of the Smoke Screen. 
 
The final assembly, viewed ‘through the ceiling’ 
is in the photo. Any hole made in the ceiling 
below can be made good with a cosmetic hole 
surround. 

 

2.5 NOZZLE CHANGING 

 

To change the nozzle, first remove the front cover then remove and replace the nozzle using a 10mm ring 
spanner, sealing it with PTFE tape and ensuring that an angled nozzle is seated in the correct orientation. The 
Smoke Screen is delivered with a single-hole straight nozzle plus an extra 1-hole 30 deg angle down nozzle. The 
following are also available – 2-hole horizontal, 3-hole horizontal, 1-hole 30° angle down and 2-hole 30° angle 
down. 

 

Be aware of high voltage in the block 
area. The electrical supply should be 
switched off before working in the 
heater block compartment.

 

 

This operation is usually carried out 
during installation. If the Smoke Screen 
has been in service the nozzles will be 
extremely hot and will cause injury if 
touched. Therefore, the Smoke Screen 
should be switched off and time should 
be allowed for the nozzles to cool.

 

b

 

Содержание Sentinel S35v6
































Отзывы: