SPECIFICATION
CAUTION
INSTALLATION
1. This installation should be made by a qualified service person and should comply with all
local regulations.
2. In order to prevent electric shock and prevent damage to waterproof seals, do not loosen
any screws on the camera body.
3. Avoid installation on a surface subjected to frequent vibration or shocks.
4. Do not operate the camera beyond its temperature range or power rating.
5.
Should any damage or suspected damage occur, shutdown the power source, unplug and
contact your service provider.
6. Do not install the camera under unstable lighting conditions. Severe lighting changes or
flicker can cause the camera to work improperly.
7. Never use the camera close to a gas or oil leak.
8. Do not dismantle the camera.
9. Do not install the camera facing directly into bright sunshine, this could damage the sensor.
10. Ensure all removable covers are replaced to protect the inner components.
11. Do not install near devices which emit a strong electro-magnetic field.
12.
Use a dry or damp cloth to clean the dome sphere.
13. Do not drop the camera or subject the unit to physical shocks.
PLEASE FOLLOW THE ABOVE PRECAUTIONS – FAILURE TO DO SO MAY
INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.
Remark: Changes or modifications not expressly approved by the manufacturer can
cause the camera to be damaged and become inoperable. This may invalidate the
user warranty.
PACKING CONTENTS
Design and specification are subject to change without notice.
MODEL
SENSOR
SENSOR RESOLUTION
SIGNAL SYSTEM
SCANNING SYSTEM
SYNC. MODE
FRAME RATE
LED COUNT/TYPE
IR EFFECTIVE DISTANCE
EFFECTIVE RESOLUTION
MIN. ILLUMINATION (LED OFF)
MIN. ILLUMINATION (LED ON)
LENS
DAY & NIGHT
DIGITAL WDR
S/N RATIO
ELECTRONIC SHUTTER
WHITE BALANCE
GAIN
AE MODES
DIGITAL NOISE REDUCTION
PRIVACY MASKING
MOTION DETECTION
VIDEO OUTPUT
TRANSMISSION RANGE
SUPPLY VOLTAGE
POWER CONSUMPTION (MAX)
OPERATING TEMPERATURE
OPERATING HUMIDITY
DIMENSIONS
WEIGHT
CERTIFICATIONS
CVP9314DNIR-AHD
1/3 INCH SONY CMOS
2MP
PAL
PROGRESSIVE
INTERNAL
25fps
2 PCS IR HIGH POWER
Up to 50m
1920(H)x1080(V)
0.001Lux @ (F1.2,AGC ON)
0 Lux
2.8mm FIXED
TRUE COLOUR/MONO ICR
OFF/ON(Level 0-8)/Auto
≥50dB
1/50-1/50,000s
ATW/AWC-SET/Indoor/Outdoor/MANUAL
LEVEL 0-15
BLC/HLC/OFF
2D/3D
YES
YES
1.0Vpp, 75 OHM BNC
>300m via 75-5 coaxial cable
12VDC±10%
4.5W
MIN-25℃/MAX+55℃
90% RH MAX (non-condensing)
ΦMAX119mm x ΦMIN109mm x H91mm
410g
IP66/IK6 /CE/FCC
118mm
109mm
CONNECTION
l
Connect the video out port to your video cable
running to the monitor / recorder
l
Check the power supply is of the correct level
and connect your power supply into the power
port on the Camera.
l
View the picture on a monitoring device to
check the power and video connection are
working properly.
l
To assist in installation when using an
analogue test monitor, the camera can
be switched to an analogue output by
pushing the joystick fully left for several
seconds.
l
The camera can be returned to AHD
output by pushing the joystick fully
right for several seconds.
PSU
Troubleshooting
l
Ensure all power and cable connections are correct with the Camera and DVR.
l
If all power and cable connections are correct and the camera picture can not be
produced then contact your supplier for technical support.
Wall Plugs
X4
Conduit hole cover
opener
X1
Mounting Template
X1
Fitting Screws
X4
Dome cover
screwdriver
X1
Weatherproof
sealing washers
X8
Weatherproof
sealing pad
X1
c
14
Step 4: Adjust The Monitoring Direction
4)
Install the dome shell and compression ring on the
camera mounting base. Adjust the camera
monitoring direction, then fix the screw to finish the
installation, as shown in Figure 4.
2
1
1a
1
1b
12
13
Step 1: Take Out The Compression Ring
1a)
Open package, take out the camera, unscrew
the screw, and take out the compression ring, as
show in Figure 1a.
1b)
If the side cabling mode is used, cut open the
compression ring outlet as shown in Figure 1b.
Step 2: Drill Holes
2)
Stick the positioning label on the wall, and drill
holes based on the marks on the positioning label.
See Figure 2.
Step 3: Fix The Camera Mounting Base
3)
Insert wall plugs into the drilled holes, and fix the
camera mounting base to the ceiling (or wall) with
self-tapping screws, as shown in Figure 3.
118mm
109mm
118mm
109mm
118mm
109mm
118mm
109mm
118mm
109mm
DIMENSIONS
b
All installation methods
Loosen the three tamper screws using the provided allen key. Lift the dome cover.
NOTE: If you plan to use conduit fitting, remove conduit cap using the provided conduit key.
Method 1 - Surface Mount
Use the included mounting template (installation option 2) to mark and pre-drill the required holes.
Remove 2 of the 3 base locking screws. Use 2pc of the 2.8” screws to mount the camera directly to
the mounting surface.
Remove the 3rd base locking screw and install the 3rd 2.8” screw.
Method 2 - Surface Mount
2b. Use the included mounting template (installation
Option 1) to mark and pre-drill the required holes.
2c. Remove the camera base by unscrewing the 3 base
locking screws, and turn camera module approx. 5
degrees counterclockwise to detatch camera base from
the camera module.
2d. Install the base to the correct holes as indicated on
the mount template using the 1.2” screws.
Go to step 3a to complete installation.
VANDAL RESISTANT DOME INSTALLATION