Position A
Position B
CLEANING AND DISINFECTING YOUR BATH SPA
1) Your Bath Spa can be cleaned with any mild detergent or soap.
Cleaning is recommended after each use.
2) Disinfect your unit periodically to keep it bacteria_free. With frequent use,
disinfect weekly. With infrequent use, disinfect after each use.
RECOMMENDED MASSAGING TIMES
Spa massage should generally last only 15-20 minutes.
Caution: Read safety rules and operating instructions carefully. This product is intended for indoor
use on permanent, right wall tubs. Do not use outdoors or on the walls of inflatable tubs or pools.
HOW TO ATTACH YOUR BATH SPA
TO YOUR TUB
1) Make sure unit is disconnected from the charger and the power knob is in the “OFF” position.
The tub should be clean and empty of water.
2) Extend the folding arm and place unit along edge of tub so the unit is inside the tub and
the arm is resting on edge (Fig. 3).
3) Moisten suction cups to increase grip.
4) Secure suction cups by gently applying even pressure on bath spa against tub wall (Fig. 4).
5) Adjust suction cup on arm so that it adheres directly onto bathtub edge. See Suction Cup Position
Adjustment section.
6) Adjust height of motor assembly to desired depth by moving motor housing up or down by hand.
Built-in detents will hold the position you desire (Fig. 5).
7) Water may spray if unit is not level when turned on.
SUCTION CUP POSITION ADJUSTMENT
Suction cup underneath the handle can be in 1 of 4 positions to suit different bathtubs. (See Fig. 6)
Loosen, remove and then replace screw after adjustment.
Position A: The outer most position for thick-sided tubs.
Position B: The inner most position for thin-sided tubs.
ONE YEAR LIMITED WARRANTY
Conair will repair or replace, at our option, your appliance free of charge for 12 months
from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center nearest you,
together with your sales slip and $7.50 for postage and handling.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12 MONTH DURATION OF THIS
WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or
consequential damages, so the above limitation may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from province to province.
Service Centre:
Conair Consumer Products Inc.
156 Parkshore Drive
Brampton, Ontario
L6T 5M1
Visit us on the web at: www.conair.com
IB-3996
©2001 Conair Consumer Products Inc.
BTS4C
Brampton, Ontario L6T 5M1
01CN1415
FITTING AND REMOVING FILTER CAPS
TO REMOVE CAPS
1) Turn cap about 20˚ counterclockwise (Fig. 7).
(Filter caps are located on either side of the motor assembly.)
2) Line up single hash mark on cap with
the center seam on the back body of the unit.
3) Pull cap away from unit.
4) Rinse cap under water to remove hair, lint, etc.
TO REPLACE CAP
1) Push cap into body so that single hash mark
on cap lines up with the center seam
on the back body of the unit.
2) Turn cap clockwise about 20˚ until the double
hash marks on the cap line up with the center
seam on the back body of the unit.
WARNING: Protect from excess lint, hair, etc... from easily getting caught
in motor, unit should never be used with the filter mesh removed. Injury
or damage to unit could result.
(Fig. 7)
(Fig. 6)
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
I N S T R U C T I O N B O O K L E T F O R B T S 4 C M O D E L S
®
B
O
D
Y
B
E
N
E
F
I
T
S
TM/MD
(Fig. 3)
(Fig. 5)
(Fig. 4)
C O R D L E S S
Dual Jet
BATH SPA
