Comtrol WR7802-XT Series Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 128

background image

68 - System Configuration | Rate Control Page

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Configuration Using the Web User Interface

System Configuration | Rate Control Page

Limit Packet Type and Rate is a form of flow control used to enforce a strict bandwidth limit on a port. You
can program separate transmit (Egress Rule) and receive (Ingress Rule) rate limits at each port, and even
apply the limit to certain packet types.

Click the

Apply

button to apply the configuration changes.

Note:

You must

Save

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Rate Control

Packet type

You can select the packet type that you want to filter.

The packet types of the Ingress Rule listed here include:

All

,

Broadcast

Only

,

Broadcast/Multicast

and

Broadcast/ Multicast/ Unknown Unicast

. The

packet types of the Egress Rule (outgoing) only support all packet types.

Rate

This column allows you to manually assign the limit rate of the port.
Valid values are from 1Mbps-1000Mbps, and Zero means no limit.

Ingress Rate

Increments of 1Mbps.

Egress Rate

1 Mbps to 100 Mbps, increments of 1Mbps. 100 Mbps to 1000 Mbps,
increments of 10Mbps.

Beta

Version

«
...
68
69
70
71
72
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 2

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: National Instruments Страницы: 162

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

TOWERCHRON DP72

Бренд: Grasslin Страницы: 2

Бренд: Oracle Страницы: 112

Бренд: ZyXEL Communications Страницы: 125

Бренд: Juniper Страницы: 7

Бренд: TP-Link Страницы: 7

Бренд: Lanner Страницы: 59

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

Бренд: Comelit Страницы: 19

Бренд: Idis Страницы: 16

S3000-EI Series

Бренд: Quidway Страницы: 16

Бренд: ZyXEL Communications Страницы: 8

Бренд: Alcatel-Lucent Страницы: 12

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды