Comtrol WR7802-XT Series Скачать руководство пользователя страница 67

Страница: 67 / 128

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Switch Configuration | Port Control Page - 65

Configuration Using the Web User Interface

Switch Configuration | Port Control Page

Use this page to configure the router.

Click the

Apply

button to activate the settings.

Note:

You must

Save

(

Page 115

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Refresh

Reloads the all of the port information.

Port Control Page

State

Enable or disable the state of this port. The default setting is

Enable

which means all the ports are workable when you receive the device.

Speed/Duplex

You can configure port speed and duplex mode at each port.

Ports 1and 2

: The factory default is AutoNegotiation, it will based on

transmission to auto negotiate the speed and duplex mode. You can also
select 10 Full, 10 Half, 100 Full or 100 Half.

Ports 3 and 4

: The ports represent the SFP fiber ports. Factory default is

1000, which means that the port is in Gigabit speed. You will need to
configure to 100 if you use 100M SFP transceiver.

Note:

It is necessary to reset system, if the SFP configuration was
changed.

Flow Control

This enables or disables flow control.

Enable

means that you need to activate the flow control function of the

remote network device in order to let the flow control of that
corresponding port on the router to work.

Disable

means that you do not need to activate the flow control function of

the remote network device, as the flow control of that corresponding port
on the router works anyway.

Port Status Page (Continued)

Beta

Version

Содержание WR7802-XT Series

































































































































Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды

Comtrol WR7802-XT Series, Руководство пользователя

Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды