Comtrol WR7802-XT Series Скачать руководство пользователя страница 51

Страница: 51 / 128

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

System | DHCP Server Page - 49

Configuration Using the Web User Interface

System | DHCP Server Page

Use this page to configure the DHCP server.

DHCP Server Page

DHCP Settings

You can

Enable

Disable

this option.

After the DHCP Server option is enabled, you can then assign the
starting and ending IP of the DHCP IP address range. The WR7802-XT
allows you to assign up to one Class C range which is 255 IP addresses.

Note:

The maximum connections per session is 64.

DHCP IP Address
Range Start

This is the starting IP address that DHCP will assign. The default is
192.168.250.100.

DHCP IP Address
Range End

This is the ending IP address that DHCP will assign. The default is
192.168.250.200.

DHCP Subnet Mask

This is the DHCP subnet mask. The default is 255.255.255.0.

DHCP Gateway

This is the DHCP gateway address. The default is 192.168.250.250.

WINS1/2

This is the primary and secondary DNS servers IP addresses.

Primary/Secondary
DNS

The DNS server address that you want the DHCP server to distribute.

Lease Time

This is the amount of time of the assigned IP addresses. The range is 15 -
44640 minutes.

Beta

Version

Содержание WR7802-XT Series

































































































































Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды

Comtrol WR7802-XT Series, Руководство пользователя

Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды