Comtrol WR7802-XT Series Скачать руководство пользователя страница 47

Страница: 47 / 128

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Status | ARP Table Page - 45

Configuration Using the Web User Interface

Status | ARP Table Page

This displays the ARP (address resolution table).

Status | DHCP Client List Page

This table shows the assigned IP address, MAC address and expiration timer of the connected DHCP client
device.

ARP Table Page

IP Address

The IP Address learnt from the interface.

MAC Address

The MAC Address learnt from the interface.

Interface

The interface that learnt the ARP packet (IP and MAC Address).

Refresh

Click to refresh the table.

DHCP Client List Page

IP Address

The assigned IP address of the connected DHCP client device.

MAC Address

The MAC address of the connected DHCP client device.

Time Expired(s)

The DHCP expiration timer of the connected DHCP client device. The
time unit is in seconds. The number can be changed on the

System | IP

Settings

page with the

DHCP Server Lease Time

setting.

Refresh

Click this button to refresh the table.

Beta

Version

Содержание WR7802-XT Series

































































































































Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды

Comtrol WR7802-XT Series, Руководство пользователя

Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды