manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Руководство по установке и настройке

Поделиться
Скачать
Comtrol InterChange VS 3000 Series Скачать руководство пользователя страница 13

Overview

13

Installing VS-Link (Novell)

Overview

VS-Link for Novell is a NetWare Loadable Module (NLM) that 
supports the InterChangeVS 3000 virtual server. The VS-Link 
software works with the following operating system releases:

The VS-Link software supports up to four InterChangeVS 3000 virtual 
servers under the control of a single Novell server. VS-Link also 
provides for “hot swapping” VS3000 units, in the event that a VS3000 
must be replaced with an identical unit while in service, and it supports 
automatic switching between primary and backup Novell servers, in 
the event that a host Novell server fails.

The following sections discuss:

•

Removing the VS-Link software.

•

Installing the VS-Link software.

•

Configuring VS-Link for use in a Novell MultiProtocol Router 
(MPR) environment.*

•

Configuring VS-Link for use in a Novell NetWare Connect (NWC) 
environment.*

•

Troubleshooting communications with external devices.

•

Replacing units in service (“Hot Swapping”)

*

This includes configuring for primary and backup server operation 
in a multiple-server environment.

Table 1. Novell Operating System Releases Supported

Operating System

Feature

NetWare 3.12

MPR 3.1A or higher and/or NetWare Connect 
2.0.30 or higher 

NetWare 4.1x

MPR 3.1A or higher and/or NetWare Connect 
2.0.30 or higher 

IntranetWare I

NIAS (Support Pack V1.0) 

Содержание InterChange VS 3000 Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды