Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 31

Страница: 31 / 96

PC104 RocketPort Option

Building Additional DB25 Loopback Plugs

Building Additional
DB25 Loopback
Plugs

Loopback connectors

are DB25 female serial port plugs that you can use to test

serial ports. The ATS-XPE is shipped with a a single loopback plug (RS-232/422)
that corresponds to your quad- or octacable type.

Note:

You can run loopback tests with Test Terminal.

Wire the following pins together to build additional plugs or replace a missing RS-
232 loopback plug:

•

Pins 2 to 3

•

Pins 4 to 5 to 22

•

Pins 6 to 8 to 20

Wire the following pins
together for an RS-422 loopback plug:

•

Pins 2 to 3

•

Pins 4 to 5

RJ45 Connectors

This illustrates the pinouts for RJ45 quad- or octacables.

Building Additional
RJ45 Loopback
Plugs

Loopback connectors

are RJ45 serial port plugs that can be used to test serial

ports. The ATS-XPE is shipped with a a single loopback plug (RS-232/422) that
corresponds to your quad- or octacable type.

Note:

You can run loopback tests with Test Terminal.

•

Pins 4 to 5

•

Pins 1 to 8

•

Pins 2 to 6 to 7

Building an RS-485
Test Cable

You can use a straight-through cable as illustrated previously, or build your own
cable.

RS-232 Only
(Back View)

The RS-232 loopback plug also works for RS-422

Pin 14

Pin 1

RS-422 Only
(Back View)

Pin 14

Pin 1

RS-232

RTS

DTR

Signal GND
TxD

RxD

DCD

DSR

CTS

Pin 1

RJ45

RS-422

TxD+

Not used

Not used**
TxD-

RxD-

Not used

RxD+

Pin 1

RJ45

RS-485

TxD/RxD+

Not used

Not used**
TxD/RxD-

Not used

Pin 1

RJ45

Pin 3 is tied to ground on the board,

but is not used in the cable.

Plug

Top View

Cable

The RS-232 loopback plug also
works for RS-422.

DB9

Pins

TxD or TRX-

RTS or TRX+

Signal

TxD or TRX-

RTS or TRX+

Signal

RJ45

Pins

RJ45

Pins

DB25

Pins

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды