Comtrend Corporation AR-5381u Скачать руководство пользователя страница 39

Страница: 39 / 206

5.2 WAN Service

This screen allows for the configuration of WAN interfaces.

Click the

Add

button to create a new connection. For connections on ATM or ETH

WAN interfaces see

Appendix D - Connection Setup

NOTE

In Default Mode, up to 16 WAN connections can be configured; while
VLAN Mux Connection Mode supports up to 16 WAN connections.

remove a connection, select its Remove

column

radio button and click

Remove.

Heading

Description

Interface

Name of the interface for WAN

Description

Name of the WAN connection

Type

Shows the connection type

Vlan8021p

VLAN ID is used for VLAN Tagging (IEEE 802.1Q)

VlanMuxId

Shows 802.1Q VLAN ID

IGMP

Shows Internet Group Management Protocol (IGMP) status

NAT

Shows Network Address Translation (NAT) status

Firewall

Shows the Security status

IPv6

Shows the WAN IPv6 address

MLD

Shows Multicast Listener Discovery (MLD) status

Remove

Select interfaces to remove

remove a connection, select its Remove

column

radio button and click

Remove.

Add

a new WAN connection, click the

Add

button and follow the instructions.

NOTE:

Up to 16 PVC profiles can be configured and saved in flash memory.

Содержание AR-5381u















































































































































































































Результаты поиска

Содержание AR-5381u

Отзывы:

Похожие инструкции для AR-5381u

Бренды по названию

Популярные бренды

Comtrend Corporation AR-5381u, Руководство пользователя

Результаты поиска

Содержание AR-5381u

Отзывы:

Похожие инструкции для AR-5381u

Бренды по названию

Популярные бренды