Comtech EF Data Vipersat SLM-5650A Скачать руководство пользователя страница 239

Страница: 239 / 516

SLM-5650A Satellite Modem

Revision 10

Serial Remote Control

10–45

MN-SLM-5650A

Parameter

Type

Controller-to-Target

Instruction Code and

Qualifier

Arguments

for Command

or Query

Description of Arguments

(Note that all arguments are ASCII numeric codes from 48 to 57)

Target-to-Controller

Command

Query

Response to

Command

Response to Query

(see Description of

Arguments)

Retrieve next 5

unread Stored

Statistics

N/A

RNS?

105 bytes

Query only.

Returns the oldest five Stored Statistics that have not yet been read

over the remote interface in the form {CR}Sub-body{CR}Sub-

body{CR}Sub-body{CR}Sub-body{CR}Sub-body, where:

Sub-body = AA.ABB.Bddmmyyhhmmss:

AA.A = Minimum Eb/No during sample period. “Loss” is displayed

if carrier was lost during the sample period

BB.B = Average Eb/No during sample period. “Loss” is displayed if

carrier was lost during the entire sample period

ddmmyyhh = date in day/month/year format

hhmmss = time in hours/minutes/seconds format

Note: If there are less than five events to be retrieved, the remaining

positions are padded with zeros. If there are no new events, the

response is RNS*.

N/A

RNS={CR}AA.ABB.Bd

dmmyyhhmmss{CR}A

A.ABB.Bddmmyyhhm

mss{CR}AA.ABB.Bdd

mmyyhhmmss{CR}AA

.ABB.Bddmmyyhhmm

ss{CR}AA.ABB.Bddm

myyhhmmss

Serial Number N/A

SNO?

9 bytes

Query only.

Used to query the unit 9-digit serial number. Returns its S/N in the

form xxxxxxxxx.

Example: >0001/SNO=176500143{CR}{LF}

N/A

SNO=xxxxxxxxx

Statistics

Sample Interval

SSI=

1 byte

Command or Query.

Sets or returns the sample interval for the Statistics Logging Function

in the form x, where:

x = 0 to 9 in 10-minute steps.

Note: Selecting 0 disables the statistics logging function.

Example: <0001/SSI=3{CR} (sets the logging inverval to 30 minutes)

SSI=

SSI?

SSI*

SSI#

SSI=x

Firmware

Revision

N/A

SWR?

43 bytes

Query only.

Returns the value of the internal firmware revision installed in the unit,

in the form:

Boot:xx.yy.zz Bulk1:xx.yy.zz Bulk2:xx.yy.zz

Example: >0001/SWR=Boot:01.01.01 Bulk1:01.01.01

Bulk2:01.01.01{CR}{LF}

N/A

SWR=Boot:xx.yy.zz

Bulk1:xx.yy.zz

Bulk2:xx.yy.zz

Содержание Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Результаты поиска

Содержание Vipersat SLM-5650A

Отзывы:

Похожие инструкции для Vipersat SLM-5650A

Бренды по названию

Популярные бренды

Comtech EF Data Vipersat SLM-5650A, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Vipersat SLM-5650A

Отзывы:

Похожие инструкции для Vipersat SLM-5650A

Бренды по названию

Популярные бренды