Computec Door Drive 5.0 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 63

Computec Door Drive 5.0 Скачать руководство пользователя страница 19

Computec

CDD5.0

EN

CDD 5.0: user manual – Rev.01

Page 19/63

4.2

Connections

4.2.1

MLC signals connection

The present paragraph reports the connections between door drive and MLC, focusing the attention on the
connection for the common voltage to use, in case it is the common voltage from door drive (24_DD) or
from MLC (24_EC). The door drive has a 24Vdc auxiliary common voltage for the wiring of commands, with
maximum load limit current of 1A.

Common Voltage

Connection

Notes

24V_DD

The 37-38 bridge must be present.
The MLC uses the 24Vdc from the door drive as
common voltage for commands and door drive
outputs.

Commands: DOC, DCC, RSC, FFC. As example only the
first two are reported in the diagram: the others
follows the same connection rules.

The door drive outputs, being dry contacts, can be
connected to another common voltage, if requested by
the MLC.

The door drive outputs have a dedicated common
voltage available for each output.
In the diagram they have been grouped in a single pin,
that represents a series of bridges between X2.4,
X2.16, X2.18, X2.35

24V_EC

Remove the 37-38 bridge and connect the external 0V
from MLC to the 38 pin.
Commands: DOC, DCC, RSC, FFC. As example only the
first two are reported in the diagram: the others
follows the same connection rules.
If local wired contacts are present:
1. use the same common voltage active for the
commands.
2. use the auxiliary 24Vdc of the door drive, recovering
the 37-38 bridges. In this case check the compatibility
between 0V_DD and 0V_EC.

The door drive outputs keep the same common voltage
from MLC, used for the commands.

The door drive outputs have a dedicated common
voltage available for each output.
In the diagram they have been grouped in a single pin,
that represents a series of bridges between X2.4,
X2.16, X2.18, X2.35

- Table 12: I/O signals connections vs MLC -

Q.M.
(E.C.)

CDD5

X2.1 (RVS N.C.)

X2.17 (DOS)

X2.19 (DCS)

X2.34 (AUXS N.C.)

X2.4 X2.16
X2.18 X2.35

X3.1.15 (+24V)

X3.2.38 (0V IN)

X3.2.37 (0V DD)

X3.1.5 (DOC)

X3.1.3 (DCC)

Q.M.
(E.C.)

CDD5

0V EC

X2.1 (RVS N.C.)

X2.17 (DOS)

X2.19 (DCS)

X2.34 (AUXS N.C.)

X2.4 X2.16
X2.18 X2.35

X3.1.15 (+24V)

X3.2.38 (0V IN)

X3.2.37 (0V DD)

X3.1.5 (DOC)

X3.1.3 (DCC)

24V EC

«
...
17
18
19
20
21
...
»

Содержание Door Drive 5.0
































































Отзывы:

Нет отзывов