Computec CDD6 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 74

Computec CDD6 Скачать руководство пользователя страница 62

Computec

CDD6

EN

CDD6: user manual – rev.07

Page 62/74

6

Maintenance

6.1

Alarms

The CDD6 door drive implements a warning/alarms/errors list, with which it can communicate functional
errors external or internal of the CDD6; these codes are very important to detect the causes of issues
during maintenance phase.

The following table reports the codes list.

“AL”

Alarm

Description

Actions

1

Parameter
mismatch

An internal parameter set integrity
error has been detected

This event automatically recovers
after internal check

2

Motor
overtemperature

The estimated motor temperature
is over the alarm threshold

Check door operator and panels,
check manually free movement of
the door, remove friction. Check
speed profiles and door duty cycle
timings

3

Lock/Unlock
failure

The locking/unlocking of the clutch
was not possible due to obstacle or
mechanical jam

Check clutch movement and remove
any mechanical jam source. Check
clutch roller and pin. The clutch has
to be free when the panels are
closed.

4

Motor connection
error

The motor has been cabled
reversing the phase wires

Check motor cable connection and
correct it

5

Motor encoder
failure

The motor encoder signal is not
working properly

Check motor encoder cable
connection

6

Motor
overtemperature

The estimated motor temperature
is over the warning threshold

AUXS output (if configured by P-07).

7

Motor jerk

The motor cable is not connected
or one single wire is not connected

Check motor cable connection and
fix it

8

Overvoltage

The maximum value of the Vbus
voltage has been reached

Check speed profile according the
moving mass, and reduce the speed
profile and/or P-A9 and/or P-C9

9

Motor output
short-circuit

There is a short-circuit on the
motor output

Check the motor integrity, and the
motor cable connection. Remove
any possible short-circuit

11

Power unit
overtemperature

The estimated temperature of the
power supply unit reached the
maximum value.

This event is automatically recovers
when the estimated temperature
decreases below the recovery
threshold. Check power
consumption related to: applied
speed profiles, moving mass, door
duty cycle.

«
...
60
61
62
63
64
...
»

Содержание CDD6











































































Отзывы:

Нет отзывов