Computec CDD6 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 74

Computec CDD6 Скачать руководство пользователя страница 52

Computec

CDD6

EN

CDD6: user manual – rev.07

Page 52/74

5.6

Output signals management

5.6.1

P-07: AUXS output options

This option permits to configure the AUXS output, that is a double contact relay.

Parameter value

Notes

00 = disabled

The AUXS output not used

01 = active during door
opening

The AUXS output is active when the door is opening. In this case it is normally
connected to an acoustic device (gong), that indicates the opening movement in
progress.

02 = space percentage

The AUXS output is active when the door position reached is higher than the space
percentage indicated by the P-08 parameter

03 = Error signal
(

default value

)

The AUXS output is active when the door drive is in alarm status, or in case of motor
overheating.

5.6.2

P-A0: DOS output activation threshold

This parameter allows to configure the DOS output activation offset. During the door opening, the
controller checks that door position reaches the door opened position, verifying:

1.

The space quote is reached

2.

The end position is reached, detecting panels hitting the bumpers

To cover installation tolerances, this parameter permits to accept door open position lower than learned
open parking position, until 40mm less.



Default value: 20mm



Range: [1 ; 40]mm

IMPORTANT: in case this offset is reached, and the DOC is deactivated, the door will anyway complete

the opening movements, keeping DOS output signal active.

The figure below shows the operating zone of the parameter:

- Figure 5-1: door opening profile and DOS activation zone -

Door
OPEN

Door
CLOSED

Skate opening

Panels opening

Door opening

DOS limit

«
...
50
51
52
53
54
...
»

Содержание CDD6











































































Отзывы:

Нет отзывов