manualshive.com logo in svg

Compaq Storage Works ESL9198 Series, Руководство по модернизации, Страница: 18 / 28

Поделиться
Скачать
Compaq Storage Works ESL9198 Series Скачать руководство пользователя страница 18

2–2     Compaq StorageWorks ESL9198 Series Tape Library Tape Drive Upgrade Guide

Tape Drive Installation

To install a tape drive: (see Figure 2-1)

1. Open the library front door.

2. Insert the tape drive 

3

 into the drive bay 

5

.

3. Secure the tape drive in the drive bay by tightening the two captive screws 

1

. These 

quick-release screws are located at the lower left and lower right corners of the tape 
drive.

4. Lower the hot-plug sensor lever 

2

.

NOTE:  

The drive position is automatically calibrated once the lever is lowered and the drive has 

been configured. During this time, the library robotics is unavailable to perform normal 
operation. If a library time-out or error message is returned as a result of issuing a robotic 
command from the library, re-issue the command after the tape drive Calibration completes. 
See Chapter 3 “

Library Configuration

” for more information.

The tape drive remains in the powered-off state until Configure completes.

The library comes pre-cabled from the factory for a two-drive-per-SCSI-bus configuration.

Содержание Storage Works ESL9198 Series





























Отзывы:

Нет отзывов