manualshive.com logo in svg

Compac COM5 PT1, Руководство по обслуживанию, Страница: 11 / 44

Поделиться
Скачать
Compac COM5 PT1 Скачать руководство пользователя страница 11

 

6. 

INTR

OD

UCTION

 

Operation 

▪

 

Following the instructions displayed on the COM5 PT1, the user inserts and removes 
their card. 

▪

 

The COM5 PT1 requests the user to select which pump they wish to refuel from. 

▪

 

The user follows on-screen prompts to authorise the transaction. The prompts will vary 
according to the type of card, the network in use and the country of use. 

▪

 

The COM5 PT1 display advises the user to take fuel. 

▪

 

After fuel has been taken and the pump nozzle hung up a receipt can be obtained by 

the customer by re-inserting and removing their card. This can be done up to 20 

minutes after the transaction 

 

Downloading COM5 PT1 Transaction Data 

EFTPOS and credit card transactions are handled by banks and transaction processing entities.  

Distributor card transactions are stored in the unit and can be downloaded via the Internet using 

the CompacOnline website www.compaconline.com. Instructions for using the CompacOnline 
website are contained in the CompacOnline User Guide. 

 

 

 

 

Содержание COM5 PT1













































Отзывы:

Нет отзывов