comoc C130 D 2015, Руководство по эксплуатации и обслуживанию, Страница: 35 / 48

EXTRAORDINARY MAINTENANCE WORK
ASSEMBLING THE SQUEEGEE BODY
To mount it the squeegee body on the machine, do as follows:
1. Bring the machine to the maintenance area.
2. Shift the direction lever (1) to “idle”, moving it in the direction shown by the arrow ( Fig.1 ).
N.B. : to select idle (N) move the lever in the direction shown by the arrow ( Fig.1 ).
N.B. : the letter “N” will appear on the command display indicating that no gear is engaged.
3. Engage the parking brake by moving the parking brake lever (2) (at the side of the operator seat)
in the direction shown by the arrow ( Fig.2 ).
N.B. : the symbol regarding the parking brake being engaged will appear on the command
display.
4. Select the “drying” program (B) ( Fig.3 ), turn the switch for adjusting the i-drive (3) in the direction
shown by the arrow ( Fig.4 ).
5. Press the drive pedal (4) to bring the squeegee body to the working position ( Fig.5 ).
N.B. : in the command display the symbols for the traction motor and the vacuum motors are
shown in green.
6. As soon as the squeegee body has reached the working position, carry out the procedures for
securing the machine (see the section “ SECURING THE MACHINE ”).
7. Using the relevant equipment loosen the screws (5) and (6) in the squeegee body pre-assembly
( Fig.6 ).
N.B.
: the equipment to be used for this operation is not supplied with the machine.
8. Insert the screw (5) in the squeegee body into the slot (7) in the squeegee support ( Fig.7 ),
making sure that the washer (8) adheres to the top of the squeegee support.
9. Repeat the operation also for the left screw (6).
10. Using the relevant equipment loosen the screws (5) and (6) in the squeegee body pre-assembly
( Fig.8 ).
N.B. : the equipment to be used for this operation is not supplied with the machine.
11. Insert the pin (9) in the squeegee body into the slot (10) on the splash guard bar ( Fig.9 ).
12. Insert the pin seal (11) into the hole on the pin (9) of the squeegee body ( Fig.10 ).
N.B. : the operation just described is valid for the right pin, repeat the operations just described
also for the left pin.
13. Insert the vacuum tube (12) into the sleeve in the squeegee body ( Fig.11 ).
NB : the squeegee has already been adjusted, but refer to “ ADJUSTING THE SQUEEGEE BODY
RUBBER BLADES ” if you need any information.
5. Press the drive pedal (4) to bring the scrubbing brush heads to the working position (
Fig.5
).
N.B. : on the command display the symbols for the traction motor and the disc brushes motors
will be green.
6. As soon as the scrubbing brush heads are in the working position, make sure the machine is in a
safe condition (read “ MACHINE SAFETY ”).
7. Remove the right brush head, unscrew the knobs (5) and shift them outward ( Fig.6 ).
8. Place the brush head body on the ground with the brush holding plates in view ( Fig.7 ).
9. Insert the brush in its seat on the brush-holder plate, turning it until the three buttons enter the slots on
the plate. Turn until the pin is pushed towards the coupling spring and is locked into place.
N.B. : the photo ( Fig.8 ) shows the rotation directions for coupling the right scrubbing brush
head, for the left one the direction of rotation is the opposite.
10. Repeat the operations in reverse order to refit everything.
FITTING DISC BRUSHES
Careful cleaning of the disc brush into the brush holder plate guarantees better cleaning of the floor as
well as a longer life of the brush motor.
To insert the brush correctly, do as follows:
1. Bring the machine to the maintenance area.
2. Shift the direction lever (1) to “idle”, moving it in the direction shown by the arrow ( Fig.1 ).
N.B. : To select idle (N) move the lever in the direction shown by the arrow, if for example gear
F is engaged ( Fig.1 ).
N.B. : the letter “N” will appear on the command display indicating that no gear is engaged.
3. Engage the parking brake by moving the parking brake lever (2) (at the side of the operator seat)
in the direction shown by the arrow ( Fig.2 ).
N.B. : the symbol regarding the parking brake being engaged will appear on the command
display.
4. Select the “scrubbing” program (E) ( Fig.3 ), turn the i-drive adjustment switch (3) in the direction
indicated by the arrow ( Fig.4 ).
FITTING THE CYLINDRICAL BRUSH
Careful cleaning of the cylindrical brush in the sweeping brush head body provides better cleaning of the
floor as well as a longer life of the brush motor.
To insert the cylindrical brush correctly, do as follows:
1. Select the i-drive program “transport” by rotating the knob to position (A”) as shown in ( Fig.1 ).
N.B. : by rotating the i-drive selector to the transfer program, all the brush heads and the squeegee
body will move to their idle positions (raised off floor).
N.B. : on the screen of the command display, the machine silhouette will have a green icon only
the symbol that identifies the traction motor
.
2. Take the machine to the maintenance area.
NOTE : the place designated for this operation must comply with current environmental protection
regulations.
3. Shift the direction lever (1) to “idle”, moving it in the direction shown by the arrow ( Fig.2 ).
N.B. : to select idle (N) move the lever in the direction shown by the arrow, if for example gear
F is engaged ( Fig.2 ).
N.B.
: the letter “N” will appear on the command display indicating that no gear is engaged.
4. Engage the parking brake by moving the parking brake lever (2), beside the operator's seat, in the
direction shown by the arrow ( Fig.3 ).
N.B. : the symbol regarding the parking brake being engaged will appear on the command
display.
35
1
1
2
3
4
3
3
B
5 5
4
6
5
10 11
9 8 7
10 5
8
11
9 5 7
9 12
2 1
1 2
4
3
3
E
5
4
8 7
6
5