comoc C130 D 2015, Руководство по эксплуатации и обслуживанию

Страница: 25 / 48

ADJUSTING THE OPERATING SPEED
To adjust the travel speed, use the knob (3) on the gear control lever (1) under the steering wheel
( Fig.4 ).
N.B. : there are three forward speeds.
N.B. : adjust the forward speed to suit the adhesion conditions.
N.B. : as soon as a speed is selected, the identification number appears on the command
display (4).
TEMPORARY ADJUSTMENT OF BRUSH PRESSURE
If, when working, you need to temporarily change the pressure exercised on the brushes, just press
the button (1) on the command display.
N.B. : pressing the button (1) renders the buttons (2) and (3) visible.
N.B. : pressing the button (2) or button (3) raises (+) or lowers (-) the pressure on the brushes.
Each time the buttons (2) or (3) are pressed, the symbol of the button (1) changes.
N.B. : there are three pressure levels: the additional pressure is zero with step-01, and
maximum with step-03.
N.B.
: the extra pressure should be selected on the basis of the type of floor and the amount of
dirt. Remember that increased pressure causes greater wear and tear on the brushes
and higher energy consumption.
N.B. : the change of pressure on the brushes is temporary, once the time has passed that was
set in the control board parameters, the pressure returns to the value pre-set in the
working program being used. To change the length of the temporary adjustment, read the
section “ CHANGING WORKING PROGRAM PARAMETERS ”.
TEMPORARILY ADJUSTING THE DETERGENT SOLUTION DISPENSED
If, when working, you need to temporarily change the dispensing of the detergent solution, just press
the button (1) on the command display.
N.B. : pressing the button (1) renders the buttons (2) and (3) visible.
N.B. : pressing the button (+) increases the solution supplied, pressing the button (-) decreases
the solution supplied. Every time the buttons (+) or (-) are pressed the button symbol
(1) changes.
N.B. : there are six detergent solution supply levels: supply is zero with step-01, and maximum
with step-06.
N.B. : the amount of detergent solution should be selected on the basis of the type of floor and
the amount and type of dirt to be removed.
CHECK SCREEN
If the “CHECK” button is pressed when working the following screen appears:
This screen allows you to carry out a diagnosis of the machine. On this screen you can view:
1. The voltage of the batteries.
2. The voltage of the traction motor.
3. The current absorbed by the traction motor.
4. The voltage of the drive pedal.
5. The power consumption of the brush motor, left scrubbing brush head.
6. The power consumption of the brush motor, right scrubbing brush head.
7. The power consumption of the sweeping brush head brush motor.
8. The power consumption of the left vacuum motor.
9. The power consumption of the right vacuum motor.
N.B.
: the modification of the amount of detergent solution is temporary, once the time has
passed by the parameters set in the control board, the amount of detergent solution
supplied returns to the pre-set value in the working program being used. To change the
length of the temporary adjustment, read the section “ CHANGING WORKING PROGRAM
PARAMETERS ”.
Press the “NEXT” button to switch to the screen for viewing the endothermic engine's parameters,
which contains:
10. Endothermic engine coolant temperature level.
11. Endothermic engine speed level.
12. Tank fuel level.
Pressing the “NEXT” button you pass to the screen that allows you to display which digital inputs of
the control board are active.
N.B.
: the grey symbols identify the components that are not active. the green symbols identify the
components that are active. the red symbols identify the components that are faulty.
25
4
3
1
1
3
2
1
3
2
6
5
1 7
3
9 8
4 2
10 12
11