manualshive.com logo in svg

CommScope SYSTIMAX iPatch Panel, Руководство для руководителей

Поделиться
Скачать
CommScope SYSTIMAX iPatch Panel Скачать руководство пользователя страница 60

Guide:

 SYSTIMAX

®

 iPatch

®

 Panel Manager Guide

4–6

Responding to Alarms

This section describes the alarms that can be generated by the iPatch Manager, the 
possible causes, and how to respond to them.

For each alarm, the possible causes and associated solutions are listed in the order 
of likelihood. After you perform the first action in the “You should…” column, press 
Menu and, with Run Diagnostics highlighted, press Select. Check to see whether 
the alarm is still in the list. If the alarm still exists, perform the next action in the “You 
should…” column and run the diagnostic tests again. Continue until the alarm no 
longer appears in the list.

You notice this alarm…

Possible causes include…

You should…

Network Manager Not Communicating

a. iPatch Manager selected to communicate 

with System Manager (Rack Manager Plus 
or Panel Manager with Network Manager 
module installed) is not configured 
properly.

a. At the iPatch Manager display, make sure that 

the iPatch Manager selected to communicate 
with System Manager is configured properly. 
The Network setting should be set to Off. (For 
the Panel Manager with Network Manager 
module installed, see page 2–16. For the Rack 
Manager Plus, see the 

SYSTIMAX

®

iPatch

®

 

System Rack Manager Plus Guide.)

b. iPatch Manager has failed.

b. Replace the iPatch Manager. (See page 5–8.)

Network Manager Not Found

a. Patch cord connecting the Network 

Manager module to the Panel Manager is 
loose.

a. Check the patch cord. If it is loose, secure both 

ends of the patch cord.

b. Patch cord connecting the Network 

Manager module to the Panel Manager has 
failed.

b. Disconnect the patch cord and connect a 

working patch cord. If the problem is fixed, 
replace the failed patch cord.

c. Power adapter is not securely connected 

from the Panel Manager with Network 
Manager module to the electrical service 
outlet.

c. Check to see whether the power adapter is 

properly connected to a PWR IN jack on the 
back of the Network Manager module and to 
the electrical service outlet. If it is not 
connected, connect it.

d. Power is not working at one or more of the 

electrical service outlets.

d. Check to see whether power is working at the 

electrical service outlet. If it is not, restore 
power to the electrical service outlet.

e. The Network Manager module has failed.

e. Replace the Network Manager module. (See 

page 5–8

.

)

No Panels Found

a. No iPatch Panels are connected to the 

panel bus.

a.

If iPatch Panels are installed

, connect the 

panels and modules to the panel bus.

If no iPatch Panels are installed

, no response is 

necessary.

b. Panel bus jumper connecting the iPatch 

Manager to the panel bus is loose, upside 
down, or not connected.

b. Check the panel bus jumper. If the jumper is 

loose, secure both ends of the jumper. Make 
sure the polarized tab on the connector is 
inserted into the opening in the header on the 
panel bus.

c. A connector on the panel bus was 

momentarily shorted during installation.

c. Remove power from the iPatch Manager and 

then restore power.

continued

Содержание SYSTIMAX iPatch Panel
























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды