manualshive.com logo in svg

CommScope SYSTIMAX iPatch Panel, Руководство для руководителей

Поделиться
Скачать
CommScope SYSTIMAX iPatch Panel Скачать руководство пользователя страница 27

Chapter:

 Installing the iPatch Equipment

2–11

Task E. For Each Rack with iPatch Panels, Install the Panels

Important: 

To use iPatch Fiber Shelves in an existing iPatch System, the iPatch 

Manager units (and any Network Managers) must be running a compatible software 
version. To determine which software versions are compatible with your iPatch 
Fiber Shelves, refer to the installation instructions provided with the shelves. To 
obtain the latest version of software, contact your SYSTIMAX Solutions local 
account representative.

1

Install the iPatch Panels on the rack. For instructions, see the installation 
instructions provided with the panel.

Important: 

Make sure that each iPatch Panel is securely connected to the panel 

bus. The most common problems that occur with equipment installation are 
due to improper panel bus jumper connections at the panel or at the panel bus.

2

For a Panel Manager

, connect the power adapter plug to the PWR1 jack on the 

back of the Panel Manager

. Route the power adapter cord along the display 

patch cord. Use the strain relief strap to secure the power adapter cord to the 
display patch cord.

For a Panel Manager with a Network Manager module installed

, connect the 

power adapter plug to the PWR IN1 jack on the 

back of the Network Manager

. 

Route the power adapter cord along the patch cord connected to the Panel 
Manager.

Note: 

Remove the strain relief strap from the Panel Manager display patch 

cord. It will be used in Task H to provide strain relief for the power adapter cord.

Figure 2–10 Connecting the Power Adapter

Strain relief strap

Power adapter cord

Power adapter cord

Panel Manager

Panel Manager with Network Manager Module

Содержание SYSTIMAX iPatch Panel
























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды