manualshive.com logo in svg

CommScope SYSTIMAX imVision X, Руководство пользователя

Поделиться
Скачать
CommScope SYSTIMAX imVision X Скачать руководство пользователя страница 22

www.commscope.com 

 

User Guide 860633028 

June 2018 

 

 

Page 22 of 30 

© 2018 CommScope, Inc. All Rights Reserved 

Multi-Rack Information on the Ready Screen 

 

The ready screen shows the rack numbers and rack names in locations that correlate to where the dependent racks are 
located. The center rack number and name correspond to the imVision Controller X’s rack. The rack numbers and names on 
the left and right sides of the ready screen correspond to the dependent racks to the left and to the right of the imVision 
Controller X’s rack.  
The top bar, which shows most of the time in other screens as well, shows on which side of the Controller X’s rack each 
dependent rack is located.  
If a rack number or rack name is pressed, the imVision Controller X will display rack information for that rack. 

Tabbed Screens 

         

 

Some screens will have a tabbed interface to indicate separation of information according to each rack managed by the 
imVision Controller X. Select the tab of the rack you would like to see and that rack’s information will be displayed. 
 

Firmware Management 

Determining Current Firmware Versions 

Firmware versions for imVision Controller X’s in a zone can be determined in any of the following ways: 

•

 

Each imVision Controller X’s firmware version may be shown on its display by pressing the Home button, then 

Tools

, 

then 

Controller Information

. 

Содержание SYSTIMAX imVision X































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды