CommScope SYSTIMAX EHD Скачать руководство пользователя страница 4

Страница: 4 / 22

TECP-91-005 • Issue 5 • October 2017

Page 4

CommScope

•

Blade—

holds adapter packs or cabled modules; slides out to two front access

positions and is removable from front. There are three blades per RU rack space.

Figure 1. SYSTIMAX EHD Panel Main Components (2RU Model Shown)

•

Fiber Cover—

holds down fibers on each blade to prevent them from being

inadvertently snagged or misrouted.

•

Grounding Location—

is where a two-hole lug and ground wire are attached to

connect panel ground PEM nuts to office ground. A two-hole lug is provided with
the product; the ground wire is not.

•

Mounting Brackets—

can be flipped around to provide either front- or rear-facing

mounting on a channel rack.

•

Front Door—

swings down to provide access to the interior of the panel. The door

features a double hinged design that allows users to open the door without
interfering with equipment below the panel on the same rack, or also to allow the
door to lay flat for easy access to the bottom blade.

•

Designation Label—

provides physical space for recording fiber designations.

•

Duplex LC Adapter Pack—

(shown for reference) mounts within the blade.

Product offerings for adapter packs include LC adapter packs in singlemode APC
or UPC style.

Note:

In this figure, the 2RU panel is shown. Main components are analogous for

other RU sizes.

26380-A

DUPLEX LC

ADAPTER PACK

(SHOWN FOR
REFERENCE)

MOUNTING

BRACKET (2X)

BLADE (6X)

(FULLY REMOVED

FROM CHASSIS)

DESIGNATION LABEL

FRONT

DOOR

GROUNDING

LOCATION

FIBER

COVER (2X)

Содержание SYSTIMAX EHD























Результаты поиска

Содержание SYSTIMAX EHD

Отзывы:

Бренды по названию

Популярные бренды

CommScope SYSTIMAX EHD, Руководство пользователя

Результаты поиска

Содержание SYSTIMAX EHD

Отзывы:

Бренды по названию

Популярные бренды