CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 78

Страница: 78 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Ruckus ICX 7750 Specifications

Power consumption (maximum configuration)

Power consumption (maximum configuration)

All ports connected with optics to draw maximum power per MSA Optics Specification. Traffic at full rate or 100% throughput. Fans at full
speed.

Power consumption (modules)

Data port specifications (Ethernet)

Serial port specifications (pinout mini-USB)

Model name

@100 VAC input

@200 VAC input

@-48 VDC input

Minimum number of
power supplies

Notes

ICX 7750-26Q

319 W

1088 BTU/hr

350 W

1194 BTU/hr

350 W

1194 BTU/hr

1 AC or DC

Fans at high speed

ICX 7750-48F

290 W

989 BTU/hr

327 W

1116 BTU/hr

327 W

1116 BTU/hr

1 AC or DC

Fans at high speed

ICX 7750-48C

558 W

1904 BTU/hr

586 W

2000 BTU/hr

586 W

2000 BTU/hr

1 AC or DC

Fans at high speed

Module name

Module description

Power consumption

ICX 7750-6Q

6-port 10/40 GbE QSFP+

Typical = 18.8 W

Maximum = 25.9 W

Model

Port type

Number of ports

Description

ICX 7750-26Q

40 GbE

QSFP+, 10/40 Gbps, compatible with short range (SR) and long range (LR) optical SFP
transceivers.

ICX 7750-48F

40 GbE

QSFP+, 10/40 Gbps, compatible with short range (SR) and long range (LR) optical SFP
transceivers.

10 GbE

SFP+, 1/10 Gbps, compatible with short range (SR) and long range (LR) optical SFP
transceivers.

ICX 7750-48C

40 GbE

QSFP+, 10/40 Gbps, compatible with short range (SR) and long range (LR) optical SFP
transceivers.

10 GbE

10GBASE-T, 1/10 Gbps, capable of auto-negotiating link speed.

Pin

Signal

Description

Reserved Not

used

UART0_RX

Data received by ICX

UART0_TX

Data transmitted by ICX

Reserved Not

used

GND

Ground

Содержание Ruckus ICX 7750



























































































Результаты поиска

Содержание Ruckus ICX 7750

Отзывы:

Бренды по названию

Популярные бренды

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Результаты поиска

Содержание Ruckus ICX 7750

Отзывы:

Бренды по названию

Популярные бренды