CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 59

Страница: 59 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Ruckus ICX 7750 Operation

LED patterns

TABLE 18

40 GbE mode QSFP+ port LEDs (left-side LED)

LED state

Status of hardware

Recommended action

Off (no light)

Not cabled.

No action required.

Steady green

Link is up in 40 GbE mode.

No action required.

Blinking green

There is 40 GbE traffic and packets are being transmitted or
received.

No action required.

TABLE 19

4x10 GbE mode QSFP+ port LEDs

LED state

Status of hardware

Recommended action

Off (no light)

Not cabled.

No action required.

Steady amber

Port lane link is up in 10 GbE mode.

No action required.

Blinking amber

There is 10 GbE traffic and packets are being transmitted or
received.

No action required.

TABLE 20

10/100/1000 Mbps UP and DN Ethernet port LEDs

LED state

Status of hardware

Recommended action

Off (no light)

Not cabled.

No action required.

Steady green

Link is up in 1 GbE mode.

No action required.

Blinking green

There is 1 GbE traffic and packets are being transmitted or
received.

No action required.

Steady amber

Link is up in 10/100 Mbps mode.

No action required.

Blinking amber

There is 10/100 Mbps traffic and packets are being transmitted or
received.

No action required.

TABLE 21

Power supply unit LED

LED state

Status of hardware

Recommended action

Off (no light)

PSU is not powered on.

Verify that the PSU power cord is connected to a
functioning power source.

Steady green

PSU is on and functioning properly.

No action required.

Blinking green
(with power cord connected)

External AC input parameters are within an acceptable range but
there is no DC output or it is disabled.

Replace the power supply.

Steady amber

PSU has no DC output.

Replace the power supply.

TABLE 22

Expansion module power LED

LED state

Status of hardware

Recommended action

Off (no light)

Module is not powered on.

No action required.

Steady green

Module is on and functioning properly.

No action required.

Steady amber

Module is on and booting up.

No action required.

TABLE 23

Fan tray LED

LED state

Status of hardware

Recommended action

Off (no light)

Fan tray is not powered on.

No action required.

Содержание Ruckus ICX 7750



























































































Результаты поиска

Содержание Ruckus ICX 7750

Отзывы:

Бренды по названию

Популярные бренды

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Результаты поиска

Содержание Ruckus ICX 7750

Отзывы:

Бренды по названию

Популярные бренды