CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 29

Страница: 29 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)

•

#2 Phillips torque screwdriver

•

1/4-inch slotted-blade torque screwdriver

Parts list

The following parts are provided with the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks Installation (XBR-R000295).

FIGURE 14

Rack kit parts

Flush-front mounting the device in the rack

CAUTION

Use the screws specified in the procedure. Using longer screws can damage the device.

Front brackets (2)

Screw, 8-32 x 5/16-in., panhead Phillips (8)

Bracket extensions (2)

Screw, 8-32 x 5/16-in., flathead Phillips (16)

Rear brackets, short (2)

Screw, 6-32 x 1/4-in., panhead Phillips (8)

Rear brackets, medium (2)

Screw, 10-32 x 5/8-in., panhead Phillips (8)

Rear brackets, long (2)

10 Retainer nut, 10-32 (8)

CAUTION

The device must be turned off and disconnected from the fabric during this procedure.

Содержание Ruckus ICX 7750



























































































Результаты поиска

Содержание Ruckus ICX 7750

Отзывы:

Бренды по названию

Популярные бренды

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Результаты поиска

Содержание Ruckus ICX 7750

Отзывы:

Бренды по названию

Популярные бренды