background image

Page 8 of 8

© 2019 CommScope, Inc. All Rights Reserved

15 

Trade-marks 

All trademarks identified by ® or ™ are registered 

trademarks or trademarks, respectively, of CommScope, 

Inc. This document is for planning purposes only and is 

not intended to modify or supplement any specifications 

or warranties relating to CommScope products or services. 

CommScope is committed to the highest standards of 

business integrity and environmental sustainability, with a 

number of CommScope’s facilities across the globe certified 

in accordance with international standards, including ISO 

9001, TL 9000, and ISO 14001.

Further information regarding CommScope’s commitment 

can be found at

www.commscope.com/About-Us/Corporate-Responsibility-

and-Sustainability.

This product may be covered by one or more U.S. patents or 

their foreign equivalents. For patents, see www.cs-pat.com.

16 

Contact information

Visit our website or contact your local CommScope 

representative for more information.

For technical assistance, customer service, or to report any 

missing/damaged parts, visit us at:

http://www.commscope.com/SupportCenter

13 

Mounting options

• 

Wall fixation: use mounting ears.

• 

Pole fixation: use mounting ears in combination with 

plastic or metal hose clamps.

• 

Strand mount: OFDC-C12 BRKSTRAND (To be ordered 

separately). 

14 

Overview of possibilities

Port 1 + 2: Spliced

Port 3 + 4: TAP with SC APC connectors 

Port 5: FIC with 900 µ overlength storage 

Port 6: Pre-connectorized LC APC duplex

Port 7: SC UPC 

Port 8: LC UPC duplex

1  2  3  4      5  6  7  8

Содержание OFDC-B8G









Отзывы: