CommScope OFDC-A4 SPLICE/PATCH страница 9 Скачать руководство пользователя

Страница: 9 / 10

Page 9 of 10

8�2

Drop connections

8.2.1

Install the pre-connectorized cable as shown.

Secure the cable jacket to the external bracket with foam and

cable ties. In case of field installable connectors (FIC), store

the 900 µ overlength as shown. If presence of aramid yarn,

secure properly with the screw.

8.2.2

Ideal length: 20-25 cm / 7.8-9.8 inches).

Extra features

9�1

Splitter or TAP in tray 2

This option consumes 1 module of 12 splice holders.

9�2

ANT splice holders

8.1.3

Route the pigtails trough the slit of tray 2.

8.1.4

Install the feeder cable (single or looped) and

secure properly (see section 6.1). Route the bundle via the

ktu to tray 2.
8.1.5

For splicing on tray 2 see section 6.3.

Содержание OFDC-A4 SPLICE/PATCH











Результаты поиска

Содержание OFDC-A4 SPLICE/PATCH

Отзывы:

Похожие инструкции для OFDC-A4 SPLICE/PATCH

Бренды по названию

Популярные бренды

CommScope OFDC-A4 SPLICE/PATCH, Руководство по установке

Результаты поиска

Содержание OFDC-A4 SPLICE/PATCH

Отзывы:

Похожие инструкции для OFDC-A4 SPLICE/PATCH

Бренды по названию

Популярные бренды