manualshive.com logo in svg

CommScope ION-U EU L 17EP/17EP, Руководство пользователя, Страница: 49 / 66

Поделиться
Скачать
CommScope ION-U EU L 17EP/17EP Скачать руководство пользователя страница 49

4. Commissioning 

 

 

M0200AJA_ION-U_EU_L_17EP_17EP.docx   

User’s Manual for ION

®

-U 

Page 49 

 

4.2.8.  Control connector RS-232 LOCAL- Local Interface 

These  DB-9  female  connectors  are  used  for  local  access  to  this  EU  part  and  for 
external modem communication between this EU and an ad

ditional “downstream” EU. 

 

 

 

DB-9 Female 

PIN 

Assignment 

1 

Booster presence IN 

2 

RS232 Tx 

3 

RS232 Rx 

4 

n.c. 

5 

GND 

6 

n.c. 

7 

n.c. 

8 

Booster presence OUT 

9 

n.c. 

figure 4-25 RS-232 connector 

table 4-5 RS-232 connector, pin assignment 

Connect the RS-232 cable (1.5m, contained in delivery of EU) from the LOCAL port of 
this EU to the C

TRL port of the “downstream” EU. 

4.2.9.  Control connector RS-232 CTRL 

These DB-9 male connectors are used for external modem communication between 
this EU and an “upstream” RU or EU.

 

 

 

DB-9 Male 

PIN 

Assignment 

1 

Booster presence OUT 

2 

RS232 Rx 

3 

RS232 Tx 

4 

n.c. 

5 

GND 

6 

n.c. 

7 

n.c. 

8 

Booster presence IN 

9 

n.c. 

figure 4-26 RS-232 connector 

table 4-6 RS-232 connector, pin assignment 

Connect the RS-232 cable (1.5m, contained in delivery of EU) from the CTRL port of 
this EU to the LOC

AL port of the “upstream” RU or EU. 

 

 

Содержание ION-U EU L 17EP/17EP



































































Отзывы:

Нет отзывов