CommScope FL2000 Storage Panel страница 16 Скачать руководство пользователя

Страница: 16 / 20

ADCP-90-516 • Rev B • April 2019

Page 16

Figure 12. Cable Storage Methods

5.2

Using the Storage Disk Panel

Use the following procedure to store excess patch cord length in a Storage Disk Panel:

1. Adjust patch cord slack so that excess length is accumulated at the storage panel.

2. Open panel front cover and select storage disk assembly that will be used to store the

excess patch cord length.

3. Press inward (toward back of chassis) on the inner side of each of the two snap tabs

(located on front of storage disk assembly) until each tab snaps open.

4. Slide storage disk assembly out of the chassis by pulling outward on the extended snap tabs.

Internal stops will prevent the disk assembly form sliding completely out of the chassis.

5. Find the midpoint of the excess patch cord slack and form a loop.

6. Place loop around one of the two retainers that are mounted in the center of the storage disk.

7. Route the two patch cord segments around the second retainer and out through the opening

in the edge of the disk assembly as shown in

Figure 13

. The routing shown for a patch

cord entering from the left side is not the same as the routing for a patch cord entering
from the right side.

Caution:

Do not kink or make a sharp bend in the patch cord when forming loop. Excessive

bending may damage the optical fiber within the patch cord

FANNING

FINGERS

(BOTH SIDES)

CAT #

S/N

DATE

CODE

MADE

IN USA

STORAGE DECK

NOTES:

1. "OVAL" CABLE ROUTING METHOD A .

2. "FIGURE 8" CABLE ROUTING METHOD B .

6956-F

CABLE A

CABLE B

Содержание FL2000 Storage Panel





















Результаты поиска

Содержание FL2000 Storage Panel

Отзывы:

Похожие инструкции для FL2000 Storage Panel

Бренды по названию

Популярные бренды

CommScope FL2000 Storage Panel, Руководство по установке

Результаты поиска

Содержание FL2000 Storage Panel

Отзывы:

Похожие инструкции для FL2000 Storage Panel

Бренды по названию

Популярные бренды