CommScope e-POI Скачать руководство пользователя страница 43

Страница: 43 / 86

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

© June 2021 CommScope, Inc.

Page 43

Safely Working with ERA Hardware

AFELY

ORKING

WITH

ERA H

ARDWARE

The following sections provide important information that you should read and know before working with

any ERA hardware. Observe all cautions and warnings listed in this section.

Health and Safety Precautions

Property Damage Warnings

A high leakage current ground (earth) connection to the Power Supply Unit (PSU) is essential before

making any other connections to the PSU.

Laser radiation. Risk of eye injury in operation. Do not stare into the laser beam; do not view the laser

beam directly or with optical instruments.

High frequency radiation in operation. Risk of health hazards associated with radiation from the

antenna(s) connected to the unit. Implement prevention measures to avoid the possibility of close

proximity to the antenna(s) while in operation.

Keep operating instructions within easy reach and make them available to all users.

Only license holders for the respective frequency range are allowed to operate this unit.

Read and obey all the warning labels attached to the unit. Keep all warning labels are kept in a legible

condition. Replace missing or damaged labels.

Make sure the unit's settings are correct for the intended use (refer to the manufacturer product

information) and regulatory requirements are met. Do not carry out any modifications or fit any spare

parts, which are not sold or recommended by the manufacturer.

Содержание e-POI























































































Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды

CommScope e-POI, Руководство по установке

Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды