manualshive.com logo in svg

CommScope e-POI, Руководство по установке

Поделиться
Скачать
CommScope e-POI Скачать руководство пользователя страница 35

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide 

© June 2021 CommScope, Inc.

Page 35

Power Supply Unit Subrack and Rectifier Modules

12 Vdc Rectifier Module

The 12 Vdc Rectifier Module (PN 7663610-xx) supplies power to the WCS and e-POI Subracks. The 12 Vdc 

Rectifier Module is fully redundant for ERA. 

A second 12 Vdc Rectifier Module is to provide N+1 redundancy. The following graphic and table identify the 

12 Vdc Rectifier Module LEDs and connectors. 

The 12 Vdc Rectifier Module has an operating temperature range of -10 to +55 °C (+14 to +131 °F). 

The PSU Rectifier Modules are hot swappable; you do not need to power down the PSU subrack to add 

or remove a module.

Ref # LED

LED Color Description

1

AC

Green

AC input is within the specified range of 85 to 264 Vac.

Off

AC input is not within the specified range.

2

DC

Green

DC output is within the specified range of 12V+/-2% (worst case) over line, load, and 

temperature.

Off

DC output is not within the specified range.

3

FLT (Fault) Red

There is no AC input or a failure has been detected in the 12 Vdc Rectifier Module. The Fault 

LED activates under the following conditions:
• If two 12 Vdc Rectifier Modules are installed in the PSU, and the AC input is removed (cable 

unplugged) from one of the modules. 

• If only one 12 Vdc Rectifier Module is installed in the PSU, and AC power is removed. In this 

instance the FLT LED is only momentarily red. (The PSU has significant energy storage 

capacity and takes several seconds to fully discharge when AC input power is lost, which 

allows the FLT LED to remain on for a short period after input power is disconnected.)

For assistance in determining power consumption and heat produced for a specific equipment 

configuration contact CMS Global Technical Support as described on 

page 82

.

1 2 3

Содержание e-POI























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды