manualshive.com logo in svg

CommFront DVS-232-2, Руководство пользователя, Страница: 6 / 49

Поделиться
Скачать
CommFront DVS-232-2 Скачать руководство пользователя страница 6

 

1.0 Introduction

 

 

CommFront User Manual 

 

5 

 

1.3.2 Connections 

 

 

FIGURE 1: DVS-232-2 CONNECTION DIAGRAM 

 

1.3.3 LED Indicators 

 

 

PWR Indicator 

ON: Power supply is on 

OFF: Power supply is off 

ACT Indicator 

Flashing: The unit is in working condition 

OFF: The unit is not working 

TX Indicator 

Flashing: Serial port is transmitting data 

OFF: Serial port is idle 

RX Indicator 

Flashing: Serial port is receiving data 

OFF: Serial port is idle 

 

 

10/100M Indicator 

ON: The unit is connected to a  

100M network 

OFF: The unit is connected to a 

10M network or is disconnected 

Link/Act Indicator

 

Flashing: Sending/receiving data 

OFF: No network connection 

 

1.4  Typical Applications 

CommFront device servers are designed for harsh industrial applications and provide 

a simple yet reliable solution for the following applications: 

−

 

M2M 

−

 

IIoT 

−

 

Data Acquisition 

−

 

Mass Transit 

−

 

Point of Sale 

−

 

Traffic Signals 

−

 

Security Systems 

−

 

Energy Plants 

−

 

Water and Sewage 

−

 

Medical Applications 

−

 

Factory/Industrial/Building Automation 

Содержание DVS-232-2


















































Отзывы:

Нет отзывов