Commend GE 800 Скачать руководство пользователя страница 15

Страница: 15 / 43

GE 800

4. Cabling

4.2/0617

Installation board G8A-T for 8 subscribers

Overview installation board G8A-T

Installation board G8A-I for 4 subscribers

Overview installation board G8A-I

NOTE: Connection DSP subscriber card

At DSP subscriber cards G8-GED, only “A” and “B” are connected. The first subscriber of each slot can
also be connected over the RJ45 jacks or the screw terminals (e.g. for test purposes or feed in of music).

NOTE: Connection DSP subscriber card

At DSP subscriber cards G8-GED, only “A” and “B” are connected.

GEAT 700R

(16.4 ft or 32.8 ft)

Colour code

Slot n

Slot n+1

Slot n

Slot n+1

1st subscriber

1st

2nd

3rd

: C3

subscriber

whiteblue

whiteyellow: A1

blue

brown:

whiteblue

whiteyellow: C1

yellow

black:

subscriber

2nd subscriber

whiteblue

whitegreen: A2

green

blue:

whiteblue

whitegreen: C2

brown

yellow:

subscriber

3rd subscriber

whiteblue

whitegreen: A3

black

green:

whiteyellow

whitegreen: C3

blue

brown:

4th subscriber

whiteyellow: A4

whitegreen: A4

yellow:

black:

whiteyellow: C4

whitebrown: C4

green:

blue:

parallel to D-Submin

Slot n

Slot n+1

5m or 10m cable

G8A-I

NC
NC

NC
NC
NC

NC
NC

Colour code

5 m or 10 m cable

(16.4 ft or 32.8 ft)

Slot n

1st subscriber

4th subscriber

whiteyellow:

yellow:

whiteyellow:

green:

3rd subscriber

whiteblue:

black:

whiteyellow:

blue:

2nd subscriber

whiteblue:

green:

whiteblue:

brown:

whiteblue:

blue:

whiteblue:

yellow:

Содержание GE 800












































Результаты поиска

Содержание GE 800

Отзывы:

Похожие инструкции для GE 800

Бренды по названию

Популярные бренды

Commend GE 800, Руководство по эксплуатации продукта

Результаты поиска

Содержание GE 800

Отзывы:

Похожие инструкции для GE 800

Бренды по названию

Популярные бренды