PROGRAMMING THE UNIT
BEFORE INSTALLATION
1- Before you start installation:
Verify that the vehicle is equipped with an electronic fuel injection and automatic transmission.
Verify that the vehicle starts and idles properly and inform the customer where the location of
the program/service switch will be. You must also check to see if the vehicle contains a
factory alarm system and whether it has a pin switch for the hood, if it does not have a pin
switch you must install one. Finally always use a volt/ohm meter or computer safe tester
when testing the wires.
2- Remote Start Overview:
Basic Remote Start Module Functions:
Provide the starter and ignition with a 12 volt output to start the vehicle, you may also put a 12
volt output on the accessory circuit so you will be able to turn on the air conditioning and
heater. Now you may install safety inputs to prevent the vehicle from starting at times which
can cause injury to service personnel or non authorized drivers. Furthermore you must
program the start output long enough so you can start the vehicle without damage to the
starter. Also program visual verification of the vehicle being started, such as parking lights or
LED.
3- Remote Start Basic Notes:
The remote start module senses the vehicle’s successful start By One of the following:
CURRENT,TACHOMETER,SPARK,COIL,AND VACUUM SWITCH (optional). The module will first
look for a voltage drop when the vehicle starts, if this method does not work, use the green
wire on the main harness to sense either the Tach wire, spark or coil noise. To do this you
must first place dip switch #1 to the off position. Then extend the green wire to the engine
compartment and tie the sense wire to a spark plug or a coil wire. The green wire is also
designed to connect to a Tach wire. The vacuum switch is designed to provide a ground
output until the engine is started and the switch is placed in line with one of the vehicle's
vacuum hoses. If you plan on using the vacuum switch you must place dip switch #2 to the
off position.
8
3
AUTOMATIC TRANSMISSION ONLY
DO NOT INSTALL ON MANUAL TRANSMISSION
"" Manufacturer is not responsible for any injury or damage to cars with
manual transmission ""
LOW BATTETY INDICATOR :
The Pager will indicate when it is time to replace the battery by lighting the
BATTERY symbol. this indication is not for the pager.but rater the remote transmitter. Audible
paging "beeps" will become none audible before battery replacment is necessary for the
remote transmitter.
REPLACING THE BATTERY :
Remove battery cover. and Remove old battery.
Replace with 1.5V AAA Battery
+
BATTERY
BEFORE PROGRAMING ANY TRANSMITTERS OR TESTING THE UNIT MAKE SURE THE
ANTENNA - RECEIVER IS PLUGED IN TO THE UNIT. !!!!!!!!
1- CODE TEACHING:
Turn the ignition key 3 times ON/OFF, ON/OFF, ON, the siren will chirp.
Leave the ignition key in on position, press the valet switch for 5 seconds until the siren chirps
3 times, Then press button # 1 on the remote transmitter. The siren will chirp once, if you
want to teach another transmitter with different code press # 1 on the second transmitter the
siren will chirp once. You can teach up to 2 different codes. After 10 seconds the LED starts
flashing, now the alarm has learned the code of the transmitters.
2- REMOTE PROGRAMMABLE FEATURES:
T
o enter program mode:
1-
Turn Ignition key ON
2-
Within 10 seconds press
OVERRIDE
switch 5 times. Siren will Sound with Long Chirp then
Release switch. Now in program mode.
To access feature change:
1.- Press program switch the number of times that corresponds with the feature you desire to
change.
Example:
If you want to turn feature #4 off, then press program switch 4 times.
2-
Siren and LED will flash each time switch is pushed.
3-
Press button #1 for one sec, on remote to turn feature
ON
- SIREN will chirp 1 time.
4-
Press button #2 for one sec, on remote to turn feature
OFF
- SIREN will chirp 2 times.
5-
System will automatically exit program mode.
6-
Once a programmable feature has been entered, the LED will flash the number of times
corresponding with the program feature that was chosen.
RESET TO FACTORY DEFAULT SETTING:
ENTER PROGRAM MODE (SEE ABOVE)
PRESS AND HOLD CHANNEL 3 (OR BUTTON #3 ) FOR 5 SECONDS LIGHT WILL FLASH
3 TIMES .AND ALL PROGRAMMABLE FEATURES WILL GO BACK TO FACTORY
DEFAULT SETTINGS.
(WHICH IS ALL ON)
3 SEC. DOOR LOCK PULSE
COLD START EVERY 1 HR
TRUNK OPEN WITH DISARM ALARM
RUN TIME 25 MIN.
PASSIVE
ACTIVE
PASSIVE NO LOCK
PROGRAM LOCATION
1 PULSE FOR UNLOCK
2 PULSE FOR UNLOCK
# 1
# 2
# 3
# 4
# 5
# 6
# 7
# 8
# 9
# 10
# 11
# 12
# 13
# 14
# 15
# 16
TRUNK OPEN W/O DISARM ALARM
AUTO REARM
NO REARM
CHIRP DISABLE
CHIRP WHEN ARM & DISARM
0.7 SEC. DOOR LOCK PULSE
IGNITION AUTO LOCK & UNLOCK
NO IGNITION AUTO LOCK
COLD START DISABLE
COLD START ENABLE
COLD START EVERY 2 HR
DISABLE CHIRPS ON PASSIVE
CHIRPS ON PASSIVE COUNT DOWN
ARM REPORTS IN 10 SEC.
ARM REPORTS IN 60 SEC.
RUN TIME 15 MIN.
ON
O F F
PASSIVE W/ DOOR LOCK
LOCK BEFORE & AFTER START
DISABLE
LOCK AFTER SHUTS DOWN ENGINE
DISABLE
LIGHTS 2 FLASH UPON DISARM
LIGHTS STAYS ON 30 sec. UPON DISARM
