background image

 

 

32

 

Coil alarm  

This alarm indicates that the coil element circuit is either open or interrupted. 
 

The alarm is displayed on the sterilizer in any condition when the coil circuit is NOT 
detected as closed. 

 
Perform the following checks in the order shown: 

 

Rearm the 

safety thermostat 17 

or

 17A

 by removing the plug and pressing the button 

underneath. The thermostat may be rearmed only if the 

chamber 09

 has cooled down. 

To speed up cooling, open the 

door 16

 which will however be locked. The 

door 16 

can 

be opened by turning the sterilizer on with the 

main switch13

. Press ON to display the 

message CLOSE THE DOOR? YES/NO. Press YES to start the procedure to open the door.

  

 

Check the coils with a tester for continuity without checking the value. 

 

Check TRIAC components of the 

power board 34

 and replace the electronic board 

pair, if required.

 

 

Self-filling alarm  

This alarm is present on models with the 

automatic water inlet 29 

(optional). 

 

The sterilizer will display this message in STAND BY mode only when the automatic water 
inlet is fitted (see USE AND MAINTENANCE MANUAL, chapter CONNECTIONS). 

 

 

In configuration (A)

, fill or replace the distilled or demineralized water tank. 

Note: Constantly running the pump without water will effect durability and drastically 
reduce the component’s life. 

 

Check that the inlet pipe is neither bent nor twisted. 

 

If the problem persists, check if the 

automatic water inlet pump 46 

is working. 

 

 

In configuration (B)

, check that the mains water tap is open and that the mains water 

pressure is higher than the minimum pressure indicated for the installed demineralization 

system. 

 

If the problem persists, check if the solenoid valve 

EV7 

above the water inlet opens 

correctly. 

 

In both cases

, check: 

- that all connections are properly connected; 
- that all pipes are in their seats and neither cracked nor twisted. 
 

 

Door alarm 

This indicates that the 

door 16 

is not correctly closed. 

 

The sterilizer may display this message when an attempt is made to start a cycle but the 
door is not completely locked. The sterilizer will not start in this condition. 

 

 

Close the door properly before starting a cycle. 

 

If the problem persists, despite the door being locked, 

micro-switch M1 36A 

and/or 

micro-switch M2 36B 

are not correctly pressed or are faulty. Check that: 

-

 

the lock nuts on the micro-switches are tight; 

-

 

the pin is not bent, out of its seat, or loose; 

-

 

there is continuity at micro-switch contacts (use a tester); 

-

 

there are no obstructions or dirt near the micro-switch rod; 

-

 

the connection cables between the door and the sterilizer are operating and 
properly connected. 

 

Alarms 

Содержание Sterilclave 6 B Speedy

































































Отзывы: