COMINOX Sterilclave 6 B Speedy Скачать руководство пользователя страница 11

Страница: 11 / 64

Outputs

The status of the sterilizer outputs can be displayed and modified:

•

EV1 charge to which the

water inlet pump 35

is connected in parallel

•

EV2 drain

•

EV3 3-way

•

EV4 steam

•

EV5 drying

•

EV6 by-pass

•

Water pump is the

automatic water inlet pump 46

(optional). If the sterilizer is

provided with connections to the SPEEDY WATER demineralization system,

the pump is replaced by the solenoid valve EV7.

•

Vacuum pump is the

vacuum pump 41

•

Door lock

•

Fan(s)

is the

fan 42

•

Aux 1 is not used

•

Aux 2 is not used

•

External coil for pre-heating and drying

chamber 09

•

Internal coil for steam generation

Note:

The external coil is the series of lower and upper coils external to the

chamber 09

The internal coil is the coil internal to the

steam generator 47.

Use the

↑↓

arrows to scroll the list and highlight the required option. Press ENTER to change

the output state (ON/OFF).
Press

to go back to the Technician Menu.

Technician Menu

Содержание Sterilclave 6 B Speedy

































































Результаты поиска

Содержание Sterilclave 6 B Speedy

Отзывы:

Похожие инструкции для Sterilclave 6 B Speedy

Бренды по названию

Популярные бренды

COMINOX Sterilclave 6 B Speedy, Руководство по обслуживанию

Результаты поиска

Содержание Sterilclave 6 B Speedy

Отзывы:

Похожие инструкции для Sterilclave 6 B Speedy

Бренды по названию

Популярные бренды