manualshive.com logo in svg

Comfee CMP10, Инструкция по эксплуатации, Страница: 18 / 20

Поделиться
Скачать
Comfee CMP10 Скачать руководство пользователя страница 18

16

How To Replace The RO Membrane Filter Element

1. Your Reverse Osmosis membrane usually has a useful life of about 2-3 years. The useful 

life of filter membrane depends on the quality of source water, household water consumption 

and the frequency of replacing 1st to 3rd filter element. 

NOTE: In order to ensure the 

performance of the system and the purity of water, please replace the 1st to 3rd filter 

element as planned.

2. Please open the RO water faucet to reduce the system pressure, and place a towel under 

the machine. It is a good idea to have a bucket handy to dump the water in the filter housing.  

Note: When you unscrew the filter cap from the RO membrane filter housing, water will 

be present in the filter housing. Place a water bucket close to the RO filter cap to 

capture any water which may spill. 

3. Remove the PE tube from the RO filter housing and unscrew the filter housing counter-

clockwise with the housing wrench.

4. It may be necessary to remove the RO filter membrane with a pair of pliers. Carefully pull 

on the filter end to slide the filter out of the filter housing. 

Note: The RO filter has a very 

tight fitting inside the RO filter housing. Pulling out the RO filter membrane can be 

difficult.

5. Inspect the inside of the RO filter housing. Please rinse the inside of RO filter housing 

thoroughly with warm soapy water. Use a small amount of dishwasher detergent to clean the 

inside of the RO filter housing.

6. Open the vacuum-tight package of the new reverse osmosis membrane, remove the RO 

membrane and insert it into the filter housing. 

Note: Please try to avoid touching the filter 

membrane with your bare hands. Using a paper towel to wrap around the end of the 

filter to help you install the filter.

7. Inspect the filter cap O-Ring and internal O-Ring. Make sure both are present and installed 

correctly. 

Note: We recommend replacing the O-Ring every 3-years to prevent water 

leaks caused by an aging O-Ring.

8. Install the RO membrane housing cap and pre-tighten it by hand, and then tighten it by 

1/4-½ turns with a housing wrench, without over-tightening.

Replacement of the 5th Stage Post Carbon Filter Element

Note: Please replace the post carbon filter element every 12 months. To help you 

remember when the filter was installed, mark the outside of the filter housing with 

the installation date.

1. Remove all tubes connected to the post carbon filter housing.

2. Replace the whole filter (including the housing) with a new one, then reconnect the tubes.

Содержание CMP10





















Отзывы:

Нет отзывов