manualshive.com logo in svg

Comet System T0610, Руководство пользователя

Поделиться
Скачать
Comet System T0610 Скачать руководство пользователя страница 45

IE-SNC-Tx6xx-07 

 

 

 45  

Operating humidity and atmospheric pressure range: 

Type 

Humidity range 

Atmospheric pressure range 

T0610 

0 to 100%RH 
without condensation 

600 to 1100hPa 

T4611 
T3610 
T3611 
T7610 
T7611 
T7613D 
T6641 

850 to 1100hPa 

T5641 
T6640 

0 to 95%RH 
without condensation 

T5640 

Protection: 

Type 

Case with electronic  Sensor cover 

(or external probe with cable) 

CO

2

 probe 

T0610 

IP30 

IP40 

- 

T3610 
T7610 
T6640 
T7613D 
T3611 
T7611 
T6641 

IP65 

T5641 

- 

T5640 

- 

T4611 

depends on used Pt1000 probe 

Other environmental conditions (external influences) according to HD 60364-5-51: 

normal 

Storage conditions: 

same as the operating ranges 

Working position T3611, T4611, T7611, T5641, T6641: 

arbitrary 

Working position T0610, T3610, T7610, T7613D, T6640, T5640: 

with sensor cover downwards 

End of operation 

Disconnect the device and dispose it according to current legislation for dealing 

with  electronic  equipment  (WEEE  directive).  Electronic  devices  must  not  be 
disposed of with your household waste and need to be professionally disposed. 

Содержание T0610

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды